User manual PANASONIC CR-W402U

[. . . ] R Heavy Duty Weather Band Receiver CR-W402U APM POWER BAND CR-W402U L PWR VO LU ME/P USH SE Operating Instructions DISP · Please read these instructions carefully before using this product and keep this manual for future reference. MU TE SQ TUNE SEEK CLO 1 2 3 4 5 6 CK Safety Information Read the operating instructions for the unit and all other components of your car audio system carefully before using the system. They contain instructions about how to use the system in a safe and effective manner. Panasonic assumes no responsibility for any problems resulting from failure to observe the instructions given in this manual. This manual uses pictographs to show you how to use the product safely and to alert you to potential dangers resulting from improper connections and operations. The meanings of the pictographs are explained below. [. . . ] 162. 525 MHz Occasionally the frequency of an existing or planned station must be changed because of unexpected radio frequency interfere with adjacent NOAA weather Radio Stations and/or with other Government or commercial Operations within the area. If you have a question concerning NOAA Weather Radio, please contact your nearest National Weather Service Office. w Auto Preset Memory (APM) Press and hold [BAND] (APM: auto preset memory) for more than 2 seconds. · The 6 stations with good reception will be automatically saved in the memory under preset buttons from [1] to [6]. · Once set, the preset stations are sequentially scanned for 5 seconds each. · To stop scanning, press one of the buttons from [1] to [6] . Manual Preset Memory q Use manual or seek tuning to find a station. ( page 9) w Press and hold one of the preset buttons from [1] to [6] until the display blinks once. blinks once Preset Station Calling Press the corresponding preset button from [1] to [6] to tune in a preset station. Caution: To ensure safety, never attempt to preset stations while you are driving. Warning A weather report (including both weather forecasts and current weather reports) of NOAA broadcasting may not accord with an actual weather condition in your place. In the critical situation, you should always pay attention to the actual weather condition to safely make decisions. 10 CR-W402U CR-W402U DI SP M UTE M UTE 11 Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Note: For whatever is printed in italics in "Cause/Step" column, conduct the operations and checks by yourself. Cautions: · Do not use the unit if it malfunctions or if there is something wrong. · Do not use the unit in irregular condition, for example, without sound, or with smoke or foul smell, which can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Sound Setting Trouble Cause/Step Left and right balance, or front and rear balance is off on one side. The right speaker wire is connected to the left speaker and the left speaker wire to the right speaker. a Connect the speaker wires to the correct ones. No sound from left, right, front, or rear speaker. Left and right sounds are reversed in stereo listening. Troubleshooting Tips Common Trouble Cause/Step Vehicle's ignition switch is not on. a Turn your vehicle's ignition switch to ACC or ON. Power connector is not correctly connected. a Connect the power connector to the terminal that is always active. Power connector is not correctly connected. a Connect the power connector to your vehicle's ACC source. Grounding wire is not correctly connected. a Connect the grounding wire to a metal part of the vehicle. [. . . ] Nut (5mmø) Rear Support Strap Hex. Bolt (5mmø × 25 mm) Toothed Lock Washer (5mmø) Removal Tool (U-shaped) Power Connector Diagram Q'ty 1 2 2 2 1 1 1 2 1 Cautions: · We strongly recommend that you wear gloves for installation work to protect yourself from injuries. · When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness. (a page 18) The included Mounting Collar q is designed specially for this unit. [. . . ]