User manual PANASONIC CS-TE35TKEW

[. . . ] Order No: PAPAMY1703052CE Indoor Unit CS-TE20TKEW CS-TE25TKEW CS-TE35TKEW CS-TE42TKEW Outdoor Unit CU-TE20TKE CU-TE25TKE CU-TE35TKE CU-TE42TKE Destination Europe Turkey Please file and use this manual together with the service manual for Model No. WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. it does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. [. . . ] remote control Tab ○ Hi ○ Me ○ Me○ Lo ○ QLo [Heating]  Fan motor’s number of rotation is determined according to remote control setting. remote control Tab ○ SHi ○ Me ○ Me○ Lo ○ QLo ii Auto Fan Speed [Cooling , Dry]  According to room temperature and setting temperature, indoor fan speed is determined automatically.  When set temperature is not achieved, the indoor fan will operate according to pattern below. fan Speed Higher Medium Lower a b c d e f g [1 pattern : 10 s] h a b  When set temperature achieved, the indoor fan speed will be fixed. When thermostat off, the fan stop periodically. According to indoor pipe temperature, automatic heating fan speed is determined as follows. Immediately after the fan motor started, feedback control is performed once every second.  During fan motor on, if fan motor feedback ≥ 2550 rpm or < 50 rpm continue for 10 seconds, then fan motor error counter increase, fan motor is then stop and restart. If the fan motor counter becomes 7 times, then H19 - fan motor error is detected. 3 Outdoor Fan Motor Operation Outdoor fan motor is operated with one fan speed only. It starts when compressor starts operation and it stops 30 seconds after compressor stops operation. oN Compressor: ON Outdoor Fan: 30 sec ON OFF Fan Speed OFF ON  During cooling operation, and outdoor ambient temperature is below 8°C, outdoor fan speed will be controlled according to outdoor piping temperature as following: OD Pipe Temperature A B 26°C 33°C  During above condition, when indoor heat exchanger temperature is below 5°C, the outdoor fan will stop according to outdoor piping temperature as following: 50 AMP Air Conditioning www. 1 Vertical Airflow Operation Mode Cooling Soft Dry Airflow Direction Auto Manual Auto Manual A Heating Auto Manual B C 8 12 10 15 10 15 Inner Vane Angle (°) 1 2 3 10 ~ 45 20 10 ~ 45 20 10 30 20 20 40 50 28 36 30 45 20 32 30 45 20 32 4 5 1 Outer Vane Angle (°) 2 3 20 ~ 56 44 20 ~ 56 44 20 65 44 44 65 72 50 56 50 56 4 5 1 2 Automatic vertical airflow direction can be set using remote control; the vane swings up and down within the angles as stated above. For heating mode operation, the angle of the vane depends on the indoor heat exchanger temperature as Figure 1 below. It does not swing during fan motor stop. When the air conditioner is stopped using remote control, the vane will shift to close position. Manual vertical airflow direction can be set using remote control; the angles of the vane are as stated above and the positions of the vane are as Figure 2 below. When the air conditioner is stopped using remote control, the vane will shift to close position. There are 2 sets of ON and OFF timer available to turn the unit ON or OFF at different preset time. If more than one timer had been set, the upcoming timer will be displayed and will activate in sequence. ON Timer Control ON timer 1 and ON timer 2 can be set using remote control, the unit with timer set will start operate earlier than the setting time. This is to provide a comfortable environment when reaching the set ON time. [. . . ] When handling electronic controller, be careful of electrostatic discharge. 4 2 Remove the 8 screws of the Front Panel. 2 3 4 Remove the screw of the Terminal Board Cover. Remove the Top Cover of the Control Board by 4 hooks. [. . . ]