User manual PANASONIC CS-E7PKEW

[. . . ] Before operating the unit, read these operating instructions thoroughly and keep them for future reference. Indoor Unit INVERTER DELUXE XE series Comment utiliser l’appareil Climatiseur 12-21 English Provide maximum comfort, clean air and optimise energy saving ECONAVI and AUTO COMFORT Equipped with the human activity sensor, the air conditioner ensures to deliver cool or warm air to you, and keeps the room consistently comfortable with minimum energy consumption. Furthermore, the sunlight sensor detects the sunlight intensity and helps control heating/cooling temperatures to provide optimum comfort. It also deactivates viruses and bacteria on the filter to keep inside of the unit clean. [. . . ] AUTO HEAT COOL DRY MILD DRY FAN SPEED AIR SWING Single ECONAVI OFF/ON AUTO COMFORT MODE MILD DRY COOLING NANOE-G TEMP Multi POWERFUL/ / AIR SWING QUIET FAN SPEED POWERFUL/ QUIET To switch between powerful & quiet QUIET NORMAL TIMER ON 1 2 SET 3 Press and hold for approximately 10 seconds to show temperature setting in °C or °F. POWERFUL OFF CANCEL AC RC POWERFUL: To reach temperature quickly POWERFUL SET CHECK CLOCK RESET • This operation stops automatically after 20 minutes. Multi • Press the button again or turn OFF the unit to stop this operation. qUIET: To enjoy quiet operation Single FAN SPEED To select fan speed QUIET (Remote control display) • This operation reduces airflow noise. € For AUTO, the indoor fan speed is automatically adjusted according to the operation mode. Press the button once to use in AUTO mode. Press and hold the button until you hear 1 beep, then release to use in forced COOL mode. Press and hold the button until you hear 2 beeps, then release to use in forced HEAT mode. AUTO COMFORT To maximise comfort To set the timer 2 sets of ON and OFF timers are available to turn ON or OFF the unit at different preset times. 1 TIMER ON 1 2 AUTO COMFORT NANOE-G To purify the air 2 3 SET 3 NANOE-G OFF Cancel To deactivate viruses/bacteria on the filter NANOE-G POWER 2 Set the time 2 • After the unit is turned off, the nanoe-G in-filter deactivation may activate up to 150 minutes. Turning on the unit cancels this operation. € To disable this operation in the future, press and NANOE-G hold until a short beep sound is heard. This will not disable the nanoe-G to purify the air. € To restore the nanoe-G in-filter deactivation, press and NANOE-G hold until a long beep sound is heard. 3 Confirm SET TIMER • To cancel ON or OFF timer , press or OFF to select respective or then press CANCEL. € If timer is cancelled manually or due to power failure, you can restore the timer again by ON pressing or OFF to select respective or SET then press . • The nearest timer setting will be displayed and will activate in sequence. € When ON Timer is set, the unit may start earlier (up to 35 minutes) before the actual set time in order to achieve the desired temperature on time. € Timer operation is based on the clock set in the remote control and repeats daily once set. € In HEAT mode, if AUTO is set, the horizontal louver is fixed at the predetermined position. The vertical louver swings left/right after the temperature rises. Note ECONAVI POWERFUL/ QUIET AUTO COMFORT NANOE-G ECONAVI POWERFUL/ QUIET AUTO COMFORT , , , • Can be activated in all modes and can be cancelled by pressing the respective button again. [. . . ] use remote control to retrieve error code. 1 Press for 5 seconds TIMER ON 1 2 SET 3 2 Press until you hear beep sound, then write down the error code 3 Press for 5 seconds to quit checking OFF CANCEL AC RC SET CHECK CLOCK RESET 4 Turn the unit off and reveal the error code to authorised dealer • For certain errors, you may restart the unit for limited operation with 4 beeps when operation starts. € This may be due to damp smell emitted by the wall, carpet, furniture or clothing. Indoor fan stops occasionally during automatic • This helps to remove the surrounding odour. [. . . ]