User manual PANASONIC CU-SA9BKP5

[. . . ] Do not damage the power cord or use an unspecified power cord. Otherwise, electric shock or fire may occur. Do not plug in too many appliances to the same power socket or use the prolonged power cord. Otherwise, electric shock or fire may occur due to overheating. Do not operate the unit with wet hands. It could cause electric shock. Do not insert sticks or other objects into the air inlet or air outlet vents. [. . . ] Press CANCEL button to cancel the timer mode: one long "beep". Other operations: one short "beep". Replacing the batteries When the remote control operating range is declining, replace the batteries immediately. Please observe the following guidelines when replacing the batteries: To avoid remote control from malfunction or damaged by battery leakage, overheated, cracked and etc. , always follow the instructions below closely; Replace both batteries at the same time with new batteries. Do not use rechargeable batteries as they may differ in shape, dimensions and performance. If you do not use the remote control for an extended period of time, remove the batteries. Remarks: When the batteries are exhausted, liquid crystal display of the remote control will dimly lit or not light up. 5 How to Operate Temp. Down Button Except Automatic Operation: 1. Each press of the button will change the temperature by one degree. The adjustable temperature range is between 16 ­ 30°C. Keeping the button depressed will increase or decrease the temperature continuously. Automatic · Cooling ·Soft Dry ·Air Circulation Operations OFF/ON Button FAN SPEED AIR SWING TEMP OFF/ON MODE Fan Speed Remote Control Display ON FAN SPEED OFF AUTO LO AUTO Fan Speed Fan Speed Fan Speed Fan Speed Mode Selection Button: AUTO -Automation Operation COOL-Cooling Operation DRY -Soft Dry Operation FAN -Air Circulation Operation TIMER AIR SWING MED CANCEL SET RESET HIGH Display of air flow direction, changing as The adjustment angles of the airflow direction louvers for Cooling, Soft Dry, Air Circulation operations are different. AUTO Air Circulation Ensure that the angles of the vertical airflow direction louvers are adjusted by using the remote control. If it were manually adjusted, the proper mechanism of the louvers may be affected. If such a case, turn off the air conditioner temporarily and then restart the operation. Cooling Soft Dry About 30° During Cooling and Soft Dry operations, please avoid the vertical airflow direction louvers from positioning in a downward direction for a long period. Press operation OFF/ON button, the operation lamp of the air conditioner will flash momentarily , and then lights up. Press or button to set the room temperature. Notes: 1. The purposes of Air Circulation Operation : to maintain a good ventilation in the room; purifying and deodorizing the air. When setting the automatic airflow during Air Circulation Operation: The airflow will blow in a horizontal direction when the temperature is low, The airflow will blow in a downward direction when the temperature increases. The compressor will not operate during Air Circulation Operation. (The louvers cannot swing up and down during Air Circulation Operation) 4. When the room temperature is lower than the set temperature, Air Circulation Operation will stop. Recommendation : Select this mode when not using Cooling Operation. 7 Setting the Timer Press ON to set the ON-TIMER . Each press of the button will change the setting time by an hour in the manner of 6, 7, 8. . . . 12, 1, 2. . . . 5. (The next time when you are going to do the timer setting again, you will see the previous set time appears in the display. ) FAN SPEED AIR SWING Keeping the button depressed will forward the time by an hour continuously. [ON] will flash. hr DELAY ON Press SET to set the ON-TIMER . The timer indicator of the Indoor Unit will illuminate. FAN SPEED AIR SWING OFF/ON The remote control display will show the setting time. When you press SET button during operation, the air conditioner will stop operating automatically (Operation indicator goes off). [. . . ] Has the Intake Grille been closed properly? The remote control fails to operate? After replacing the batteries and etc. , the remote control may not be operated. In such a case, slide to open the back cover and short the "RESET" points to resume it to the normal operation. Call the Dealer Immediately If the following conditions occur, switch off the air conditioner immediately and remove the power plug. Abnormal noise is heard during operation. Switches or buttons did not operate properly. The circuit breaker tripped frequently. Water leakage occurred at the Indoor Unit. Power cord and power plug are unusually warm. 14 WARNING 1) This appliance must be earthed. [. . . ]