User manual PANASONIC CY-VMR5800N

[. . . ] Panasonic Servicenter List for Service Directory . . . Keep for future reference in case the unit needs servicing. Installation Hardware. . . Needed for monitor setting. Required Tools You'll need a screwdriver and the following: 12 V DC test Electrical tape Slide-cut bulb pliers E N G L I S H 48 Before Installation Warning Do not install the monitor in a location which obstructs driving, visibility or which is prohibited by applicable laws and regulations. If the monitor is installed in a location which obstructs forward visibility or operation of the air bag or other safety equipment or which interferes with operation of the car, it may cause an accident. Never use bolts or nuts from the car's safety devices for installation. [. . . ] Note: Some carpet materials may not be suitable for this mounting method. In this case, please contact your nearest Panasonic Servicenter for installation. Control unit Cautions: Do not install the speaker in a location which obstructs operation of the air bag or other safely equipment. Consult with a qualified servicing engineer or your dealer if other methods are required. Notes: Be sure to fully plug in the connector. Install the cord to avoid high-temperature spots and secure with clamps and tape. When game devices are connected, the image may be unstable. CY-VMR5800N When removing the DIN plug, be sure to press the clip. E N G L I S H 56 CY-VMR5800N Display unit (rear) RGB input cord To the RGB connector of the Panasonic car navigation system (not available yet). Digital signal output terminal Connect the multi channel AV control unit with receiver (CA-TU9000U). ( See the operating instructions of the CA-TU9000U. ) You need the optical fiber cable (sold separately). Video control lead To the video control lead of the Panasonic car navigation system (not available yet). Side brake (parking brake) connection lead (Blue/yellow stripe) 2 The clip connector B is connected to the power source side lead of the side brake (parking brake) lever. Take it out of the back of the tail lamp mount. Reverse lamp Clip connector Comes up to this point. Power source side lead Battery Car chassis Reverse lead (Violet/white stripe) P R N D 2 L Transmission gear Cut here. 78 CY-VMR5800N CY-VMR5800N 79 E N G L I S H 65 Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit yourself because it is dangerous to do so. Cautions: Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Common (continued) Trouble Cause/Step The volume is adjusted to zero. Set it to OFF. E N G L I S H 66 Cables are not correctly connected. The MAIN-IN is set to ON (when the digital surround processor is not connected). Set the MAIN-IN to OFF when you do not use the MAIN-IN (when the digital surround processor is not connected). Condensation (dew) Wait for a while before use. Side brake (parking brake) connection lead is not correctly connected. [. . . ] Dolby Pro Logic This format records signals from four channels [Front Left (L), Front Right (R), Center (C), and Monaural Surround (S)] in two channels, decodes those channels through a Dolby Pro Logic decoder, and then outputs the resulting signals in four channels. Rough edge dts This format requires more data than Dolby Digital, and provides higher quality surround playback. Similar to Dolby Digital, this fully discrete format divides the music signals into 5. 1 channels: Front Left (L), Front Right (R), Center (C), Left Surround (LS), Right Surround (RS) and Subwoofer (SW: 0. 1 channel) for recording and playback. Manufactured under license from Digital Theater Systems, Inc. [. . . ]