User manual PANASONIC CZ256ESMC3

[. . . ] 7 Checking the settings on the indoor unit. 8 Check Operation Setting Changing the settings on the indoor unit. 10 Settings after completing installation. 21 Changing the name of the distribution group. [. . . ] Operation Step Category step Setting Screen menu names Air conditioning operations only      *2     *2     Pulse meter settings  Distribution rate display only Time                 Load                 Quantity used, charges display Time                 Load                 1 2 Date settings Composition loading Setting the current date and time Confirming the connection configuration Central address* 1 Date settings Check configuration I/D unit settings I/D unit settings I/D unit settings I/D unit settings I/D unit settings I/D unit settings O/D unit settings A/C communication settings Area group name settings Distribution group settings Schedule group name settings Pulse meter settings Pulse meter settings Name of the indoor units Distribution group Area group 3 Unit related Control group Not batch, not managed Name of the outdoor units Local remote controller prohibition setting Name of the area group 4 Group related Name of the distribution group Name of the schedule group Association with the distribution group 5 Pulse meter related Type of pulse meter (electricity/ gas), multiplying factor (number of pulse units) Name of the pulse meter 12 CZ-256ESMC3_QR_EU. Indd 12 2016/09/12 17:13:21 Operation Step Category step Setting Screen menu names Air conditioning operations only     *6                   Distribution rate display only Time                        Load   *                     4 Quantity used, charges display Time    *5                    Load   *4 *5                    Distribution modes (time/load) Power distribution calculation target*3 Energy saving distribution setting Distribution of gas for power generation 6 Distribution related Setting the monthly cut-off days Setting the regular hour range Setting specified days Currency for electricity or gas charges*7 Setting the capacity of the indoor units*8 Setting the capacity of the electric heater*9 7 Scheduling related Schedule for a single day Allocating a schedule to a calendar Schedule group Input point (names and conditions)*10 Output point (names and operation)*11 IP address, net mask, DHCP, etc. 9 Network related*12 Setting to send alarm mails User ID, password, privileges Buzzer volume Brightness of the back light 10 Intelligent controller related Auto logout time Identification number Initialise the days accumulated data*13 Distribution mode settings Distribution mode settings Distribution mode settings Distribution mode settings Calendr sttngs for distr calc Calendr sttngs for distr calc Calendr sttngs for distr calc Distribution Ratio settings I/D unit settings I/D unit settings Schedule setting Calendar I/D unit settings Event control Event control Network settings Email settings Web user settings Display/Volume settings Display/Volume settings Display/Volume settings Initialize Initialize 8 Event control Setting *1  ttention needs to be paid to administration divisions when devices such as systems controllers are to be used in conjunction with this unit. a *2 Settings required when area administration is to be performed. *3 Select the object of calculations for electricity distributing from the following: Operating hours Thermostat on times Select when consideration is to be paid to the electricity for the indoor units. The electricity for outdoor units and indoor units are both loaded into this unit and distributed. Select when no consideration is to be paid to the electricity for the indoor units. The electricity for outdoor units only is loaded into this unit and distributed. *4  the air conditioning units included in the system are multi-function types supporting simultaneous heating and cooling or ice thermal storage models, settings If are required. *5 Settings are required only when units are GHP with generators. *6 Settings are required when only the accumulation operating time is to be managed. *7 This must be set if you want to display charges. *8 This only needs to be set for interface adaptors. *9 This is used when calculating load distributing. *12 Required when logging in through a network device to operate and monitor. *13 Clears the data calculated from test operation of the air conditioning units before hand over. Indd 13 2016/09/12 17:13:21 Setting the language and time zone Set the language to be used when setting and operating this unit. The languages available on this unit are English (US), English (UK), German, Italian, French, Spanish, and Portuguese. Set the time zone to suit the language to be used. Zz The settings are registered and the “SlctLang” dialogue closes. Find the difference between the time in the installation location of the intelligent controller and Coordinated Universal Time (UTC). If the former is 1 hour ahead of the latter, for example, select [UTC+1]. [. . . ] Indd 28 2016/09/12 17:13:32 Registering specified days Registering cut-off days 1 Touch the date for the specified day. Touch [CMth] to return to the current month. Zz The colour of the date column changes when you touch this. You cannot set a date in the past, however. [. . . ]