User manual PANASONIC CZ-CSWBC2 SOFTWARE

[. . . ] 4. Using the system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Supplementary Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. License Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7. Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Contents Precautions on Using This Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2. Startup and exit. [. . . ] Cancelling maintenance can also be performed from this screen. · BACnet number · Maintenance status : umber assigned to the indoor unit from BACnet N communication with the central monitor. :Displays the maintenance setting status. 4-1-2-1. 1. Setting Method Click the I/D unit to be set to add a check to the selection column. 2.  When is clicked, the “Set maintenance ON as for the selected I/D units (Out_Of_Service= TRUE)” message is displayed. :Settings are not performed. 3.  When the settings are performed, “Executing maintenance. . . ” is displayed in the maintenance status column.  4-1-2-2. 1.  Click the indoor unit to be cancelled to add a check mark to the selection column. Cancellation Method 2.  When is clicked, the “Set maintenance OFF as for the selected I/D units (Out_Of_Service=FALSE)” message is displayed. :Settings are not performed.  5. Supplementary Information   This system is installed on the computer that is running the CZ-CSWKC2 basic software. Please refer to this along with the Supplementary Information section of the CZ-CSWKC2 basic software instruction manual.  Selecting Objects (Control Items) If the maximum 256 air conditioning units are connected and the number of object specifications is increased, the processing speed decreases because the number of objects to be controlled increases. If faster processing speeds are required, it is necessary to increase the number of BACnet computers to reduce the number of air conditioning units connected to each.  Restarting P-AIMS When shutting down and restarting the P-AIMS system, wait for more than 10 seconds after shutdown before restarting the system. When BACnet is operating, the programs that are performing various operations require time to shut down, and may not restart if the system is restarted too soon. <Contact Information> Product ID Issuance Desk, E-mail address: cmc_productid_desk@gg. jp. panasonic. com When you make an inquiry, send the following information together with the inquiry in order to be registered as a user and issued a release key. (1) Product name (2) Company name/contact person (3) Phone number (4) E-mail address (5) Inquiry key * If you do not input a release key, you will no longer be able to use the system after 30 days elapses. Obtain a release key and perform license certification as soon as possible. * Make an inquiry as soon as possible because it may sometimes take several days to be issued a release key. License Certification Procedure The procedure from after the P-AIMS system is installed up until the end of license certification is described below. (1) Check the inquiry key from the License Certification screen. (2)  Send the inquiry key to the Product ID Issuance Desk (cmc_productid_desk@gg. jp. Also notify us of the product name, company name/contact person, phone number, and e-mail address. You are registered as a user and a release key is issued. A reply is sent to the registered mail address. (4) Input the release key from the License Certification screen. (5) The license certification procedure is finished.  Performing License Certification 1. A License Certification screen such as the following appears when you start a P-AIMS systems for which license certification is not finished. “Basic Software (25)” means that the number of remaining days that you can use the Basic Software is “25. ” It is not displayed after you finish license certification. * After you start a P-AIMS system for which license certification is not finished, the License Certification screen will appear at 9:00 a. m. This screen is not displayed after you finish license certification. If you install optional software, the License Certification screen will appear until license certification is finished for all of the software. 2. If you click the button in the License Certification screen, the Inquiry Key display screen appears, and the inquiry key is displayed in the screen. [. . . ] Click the button to complete the installation. * When installing the BACnet Software, it is possible to install this system without stopping the P-AIMS system. However, the BACnet Software functions are not added. In this case, restart the P-AIMS system. 12 7-2. Display at restart After restart, the BACnet functions become active and “BACnet” can be selected in the menu. 7-3 Settings After installation is completed, registration and settings such as “BACnet basic settings” and “BACnet indoor unit number settings” are required. Entrust the registration of “BACnet basic settings” and “BACnet indoor unit number settings” to the place of purchase or a service company. 13 User memo space If you fill this out at the time of purchase, it is convenient when ordering repairs etc. Serial No. [. . . ]