User manual PANASONIC DMR-ES30V

[. . . ] All enquiries, transactions and distribution facilities are provided directly by Panasonic UK Ltd. Also available through our internet is direct shopping for a wide range of finished products, take a browse on our website for further details. RQCAD0020 -1- Connecting with 21-pin Scart cable S =Extra equipment for the connection shown: RF cable (Aerial cable), 21-pin Scart cable 1 Aerial AV1 21-pin Scart socket AV2 DVD Recorder S VIDEO VIDEO RF IN Aerial input Y L AUDIO R RF IN PB PR OPTICAL RF OUT S RF cable / Aerial cable AV2 (EXT) AV1 (TV) AC IN~ DVD OUT AC IN~ RF OUT Aerial output 4 AC mains lead 3 S 21-pin Scart cable Necessary for TV with Q Link TV Aerial input 2 RF cable / Aerial cable 4 AC mains lead Follow the steps below. Disconnect the power of all units. 1 Connect the Aerial to the RF IN (Aerial input) of the DVD Recorder. 2 Connect the RF OUT (Aerial output) of the DVD Recorder to the Aerial input of the television set. 3 Connect the AV1 socket (21-pin Scart socket) of the DVD Recorder to the Scart input of the television set. 4 Plug the DVD Recorder and the television set into the AC mains socket. If your television set supports Q-Link, follow the steps for Auto-Setup with Q-Link on page 4. If your television set does not support Q-Link, follow the steps for Auto-Setup without Q-Link on page 4. If your television supports Q-Link or RGB, connect it to the DVD Recorder with a fully wired 21-pin Scart cable. [. . . ] ENTER: store RETURN: leave RETURN Setup without Q-Link (Automatic Tuning) Auto-Setup Ch 35 4 Auto-Setup in bitte warten. RETURN: to abort RETURN: abbrechen RETURN Owner ID PIN number * * * * Name * * * * * * * * * * * * * * House No. * * * * * * * * * * * RETURN Postcode * * * * * * * * * * * RETURN : leave Auto-Setup The automatic setup saves all available TV stations. If the station also broadcasts date and time, then the clock is also set automatically. Switch on your television and select the AV channel. With the Stand-by/on switch turn on the DVD Recorder. Automatic tuning for all available TV stations begins. After Automatic tuning has finished, press RETURN. Owner ID You can complete the Owner ID now or skip this step and do it later. To do it later, press the RETURN button. To set the Owner ID now, use and press the Numeric buttons or to enter a four-digit PIN number. Make sure that you will remember the PIN number (make a note of it). Press the ENTER button twice to confirm. Enter the [Name], [House No] and [Postcode] in the same way, using !Press the ENTER button to confirm each entry. Press the RETURN button to leave the Owner ID screen. If the clock setting menu appears (Auto clock set was not possible due to a weak signal) !Press to set the correct time and date and press ENTER to finish this setting. Mind that a wrong date or time will influence the programmed recording of TV programmes (don't forget to change summer time and winter time). If Auto-Setup has previously been completed the DVD Recorder will not start AutoSetup automatically. In this case you can re-start Auto-Setup again. If you want to cancel Auto-Setup before it has finished, press the RETURN button. See page 72 of Operating Instructions. . Clock Automatic Off Time 0 : 00 : 00 0 CHANGE ENTER No Date 1 . [. . . ] Press to select SETUP and then press ENTER. Press to select Manual and then press ENTER to display the list of tuned TV stations and confirm that all available TV stations have been set correctly. If station name is [ ]: The asterisks indicate that a station was found during Auto-Setup but has not been named (due to weak signal). The stations in the list with asterisk will need to be named manually see page 71 of Operating Instructions. If station name is [- - - -]: The dashes represent unused channel positions. [. . . ]