User manual PANASONIC DMR-ES20

[. . . ] Operating Instructions DVD Recorder Model No. DMR-ES20 Web Site: http://www. panasonic-europe. com Region number supported by this unit Region numbers are allocated to DVD players and DVD-Video according to where they are sold. The region number of this unit is "2". The unit will play DVD-Video marked with labels containing "2" or "ALL". Example: 2 ALL 2 3 5 Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before connecting, operating or adjusting this product, please read the instructions completely. [. . . ] 2 Turn on the main unit and DV equipment. 3 Pause play of the DV equipment at the point you want recording to start. When the output signal from the external equipment is NTSC, change the "TV System" to "NTSC" in the SETUP menu ( page 38). DV cable (IEEE 1394, 4-pin) S Video cable Audio/Video cable 1 2 3 4 5 While stopped Other video equipment If the audio output of the other equipment is monaural, connect to L/MONO. The S VIDEO terminal achieves a more vivid picture than the VIDEO terminal. When recording from the unit's DV terminal Select the type of audio recording from "Audio Mode for DV Input" in the SETUP menu ( page 35). When recording from DV equipment (e. g. , digital video camcorder), you can record audio/video recordings from DV tape only. Press [REC MODE] to select the recording mode. Press [e, r] to select "To Others" and press [ENTER]. Press [e, r] to select "DV AUTO REC" and press [ENTER]. Press [w, q] to select "Rec" and press [ENTER]. Recording starts. When recording finishes The confirmation screen appears. Press [ENTER] to finish DV automatic recording. To stop recording Press [g]. Note Manual recording RAM -R -RW(V) +R Preparation Connect a video cassette recorder, etc. When recording bilingual programmes When both M 1 and M 2 is selected on the connected equipment, you can select the audio type in playback. -R -RW(V) +R Select either M 1 or M 2 on the connected equipment. (The selected audio only is recorded. ) When the output signal from the external equipment is NTSC, change the "TV System" to "NTSC" in the SETUP menu ( page 38). To reduce noise in input from external equipment (e. g. , video casette recorder), set "AV-in NR" to "On" ( page 25). Check the time on the unit is correct. RAM Only one piece of DV equipment (e. g. , digital video camcorder) can It is not possible to operate the unit from the connected DV equipment. The DV input on this unit is for use with DV equipment only. (It The DV equipment name may not be shown correctly. Depending on the DV equipment, the images or audio may not be The date and time information on the tape of the DV equipment will You cannot record and play simultaneously. If the DV automatic recording function does not work properly, check the connections and DV equipment settings, and turn the unit off and back on. If that does not work, follow the instructions for manual recording ( left). cannot be connected to a computer, etc. ) be connected to the unit via the DV input terminal. RQT8212 30 DISC MANAGEMENT ShowView CANCEL Providing a disc with a name Preparation INPUT SELECT MANUAL SKIP SKIP SLOW/SEARCH DIRECT NAVIGATOR FUNCTIONS RAM Release protection ( left). 1 FUNCTIONS TOP MENU While stopped e, r, w, q ENTER SUB MENU RETURN 2 3 4 RETURN PROG/CHECK DISPLAY STATUS TIME SLIP REC AUDIO REC MODE EXT LINK CREATE CHAPTER TIMER Press [FUNCTIONS]. Press [e, r] to select "To Others" and press [ENTER]. [. . . ] If this occurs, immediately disconnect the unit from the power supply and contact your dealer. Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit. Voltage Do not use high voltage power sources. This can overload the unit and cause a fire. [. . . ]