User manual PANASONIC DMREX768

[. . . ] S 4 5 a d g j m 6 b e h k n q u x ' 7 c f i l o 8 / fl [ 9 0 ij£ l% $ ] & _ ) | ~ ; ERASE SET 0 ­ -/-- 5J 7P 8T ON@ s { z ; ( } \ ^ 6M N p t w " r v y : SELECT ENTER RETURN 9W X 0. , -/-- SPACE 1 Press [DIRECT NAVIGATOR] (9). 2 Use [3, 4] (10) to select the programme you want to erase. "Entering titles" (page 36) For your reference You can give DVD-RAM titles of up to 64 characters and DVD-R titles of up to 44 characters. The full title is shown in the "Properties" screen, but if you enter a long title, only part of it is shown in the programme list. 3 Use [1] (10) so the submenu appears. Erase Enter Title Properties Protection Partial Erase Divide Checking programme contents [RAM] [DVD-R] You can check the contents of a selected programme. [. . . ] 1) Input a 4-digit password with the numeric buttons (4) and press [ENTER] (10). Unlock Recorder: Change Password: Change Level: Temporary Unlock: To unlock the unit and return the rating to 8 To change your password To change the rating level To temporarily unlock the unit (the unit locks again if you switch it to standby or open the disc tray) *1 Audio is output at 96 kHz if the DVD is unprotected, but the connected equipment must be able to handle such signals in order to play them. 2) Select the item with [3, 4] (10) and press [ENTER] (10). Follow the on-screen instructions. Dolby Digital Bitstream (Factory preset): When you have connected a unit with a built-in Dolby Digital decoder. PCM: When you have connected a unit that doesn't have a built-in Dolby Digital decoder. *2 DTS Off (Factory preset): When you have connected a unit that doesn't have a built-in DTS decoder. *2 Bitstream: When you have connected a unit with a built-in DTS decoder. MPEG Bitstream: When you have connected a unit with a built-in MPEG decoder. PCM (Factory preset): When you have connected a unit that doesn't have a built-in MPEG decoder. *2 *2 Set "Dolby Digital" to "PCM", "DTS" to "Off" and "MPEG" to "PCM" if the other equipment doesn't have decoders. Incorrect settings can cause noise to be output which can be harmful to your ears and speakers, and audio will not be recorded properly to digital recording equipment. 62 Changing the unit's settings (continued) Remote Setting Preparation Switch [DVD, TV] (15) to "DVD". Press [FUNCTIONS] (11) to show the FUNCTIONS window. Operating other Panasonic DVD equipment with the remote control By changing the remote control code, you can operate other DVD recorders and players manufactured by Panasonic. Most of the DVD recorders and players manufactured by Panasonic use the same system for their remote controls, so if you operate them in the same place, the controls can be confused by the different pieces of equipment. Use the following procedure to change the remote control code to solve this problem. Use "1", the factory set code, under normal circumstances. Preparation Switch [DVD, TV] (15) to "DVD". 1 Use [3, 4, 2, 1] (10) to select "SETUP". The SETUP screen appears. FUNCTIONS N DVD-RAM Disc Protection Off Cartridge Protection Off N S S DISC INFORMATION DIRECT NAVIGATOR CREATE PLAY LIST SELECT ENTER RETURN TIMER RECORDING PLAY PLAY LIST SETUP TOP PLAY FLEXIBLE REC 2 Use [3, 4] (10) to select the "Settings" tab and press [2] or [1]. SETUP Remote Clock Owner ID Shipping Condition DVD 1 Press [ENTER] (10) and the numeric buttons (4) corresponding to the code you want to set, [1], [2], or [3], at the same time. Note Be sure to set the same remote control code on the main unit as you did for the remote control itself (page 59, Settings -- Remote). When "Automatic" on the Clock setting menu is set to "On", the automatic time correction function checks and if necessary adjusts the time several times every day. In case of a power failure, an automatic back-up system automatically maintains the operation of the clock for approximate 120 minutes. 6 Use [3, 4] (10) to change the setting and press [ENTER] (10). You can also use the numeric buttons (4) for setting. Clock Automatic Off Time: 15 : 45 : 39 Date: 1. 2002 CHANGE ENTER RETURN If clock setting has been completed, then please push RETURN Key. ENTER : access , RETURN : leave 7 Press [RETURN] (23). The SETUP screen reappears and the clock starts. 64 Changing the unit's settings (continued) Channel Settings Preparation Switch [DVD, TV] (15) to "DVD". Press [FUNCTIONS] (11) to show the FUNCTIONS window. Handling the TUNING BOX screen Use [3, 4, 2, 1] (10) to select the desired field and press [ENTER] (10). Pos: To change the order in which the TV stations are assigned to the programme positions. Press the numeric buttons (4) to enter the number of the desired programme position. Name: To enter or change the name of a TV station. Use [3, 4, 2, 1] (10) to enter station name and press [ENTER] (10). If the station name needs a blank space, select the blank between [Z] and [¢]. Channel: To enter newly available TV stations or change the channel number of an already tuned TV station. Press the numeric buttons (4) to enter the channel number of the desired TV station. [. . . ] 59, 62 Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25, 35 Recording modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 RESUME PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]