User manual PANASONIC EB-GD76

[. . . ] Operating Instructions Digital Cellular Phone EB-GD76 Before operating this equipment please read these instructions completely. Important Information Important Information We, Matsushita Mobile Communications Development of Europe Ltd, declare, that the EB-GD76 conforms with the essential and other relevant requirements of the directive 1999/5/EC. A declaration of conformity to this effect can be found at http://www. panasonicmobile. com/support Safety Considerations The following information should be read and understood as it provides details which will enable you to operate your phone in a manner which is both safe to you and your environment, and conforms to any legal requirements regarding the use of cellular phones. This equipment should only be charged with approved charging equipment. Other usage will invalidate any approval given to this apparatus and may be dangerous. [. . . ] For either setting or adjusting the time needed to select Power On Time or Power Off Time in the Clock Function menu. Caution: Ensure that the setting of the Alarm or Power On function will not contravene any regulations whereby it may automatically power on when in an aircraft or medical facility etc. - see "Important Information" page i. Calculator The four function calculator will enable the user to perform simple arithmetic calculations (addition/subtraction/multiplication and division). 1 From Idle Z Q, select Applications > Calculator Z Q 2 Enter a number (maximum 10 digits) and it will be displayed on the upper right of the display. If a decimal point is required, Z+ Hold 1 3 Use g to select the arithmetic operation you wish to perform (b to multiply, c to add, a to divide, d to subtract) 4 Enter a number (maximum 10 digits) and it will be displayed next to the operation symbol If g is used to select another arithmetical operation to perform, an intermediate calculation will be performed and the result displayed on the top line. 5 Z Q to complete the calculation when = is displayed in the centre of the operation field 30 Applications Currency Convertor The currency convertor enables the user to convert from/to a home currency using a conversion rate that you enter. From Idle Z Q, select Applications > Currency Z Q Entering an Initial Conversion Rate 1 2 3 4 ZQ Enter an abbreviation for the home currency (up to 3 characters) Z Q twice Enter an abbreviation for the foreign currency (up to 3 characters) Z Q twice Enter the currency conversion rate Z Q twice Converting a Value 1 Check the conversion rate is the one you require Z Q twice 2 Enter the value to be converted Z Q twice The conversion rate will be retained in the phone once entered. The next time the convertor is used, the conversion rate / currency abbreviation can be edited while in the Currency /rate display. Z Q, then use e to select Edit Z Q. Swapping the Currency Conversion When you have accepted the conversion rate and are ready to enter the value to be converted, you can swap the currencies to convert from the foreign currency into the home currency. 1 Z Q, use e to select Swap Z Q 2 Enter the value for conversion Z Q twice 31 Text Messages Text Messages It is possible to receive, display, edit and/or send text messages of up to 459 characters, (Dependant on the language being used) to mobile phones on the same network or any network that has a roaming agreement. Messages will be sent as one message, but will be received as (up to) three messages. (Dependant on the recipients phone parameters). Setting the Phone for Short Text Messages Before a message can be sent, it is necessary to enter the Message Centre number into Parameters (the Service Provider will supply the Message Centre number). The Message Centre number may have been preprogrammed on the SIM. Setting the Message Centre Number From Idle Z Q, select Messages > Parameters > Message Centre Z Q Enter message centre number in international dial format see "International Dialling" page 8 . Creating a Text Message 1 From Idle Z Q, select Messages > Create Z Q Hello Create a text message (up to 459 characters) see "Text Entry" page 58 Menu The Character menu is not available in "Numeric mode" and may only be accessed by Z Q e when using T9. To access the character menu in other text modes Z + Hold 1- 0 Z B to exit the character menu 2 Use g to navigate through the message and add or delete text 3 Z Q twice The user may be prompted to send the message, if the message is not to be sent Z C, the message will be stored. 4 Z Q and enter the destination phone number (or recall a number from the Phonebook) - see "Retrieve a Number" page 14 Z Q twice 32 Text Messages The user may be asked if delivery confirmation is required. If yes, use e to select Yes ZQ The default setting for delivery confirmation can be enabled/disabled using the Report parameter in the Parameters menu. 5 User Messages When creating a text message, it is possible to use short messages stored in the phone. 1 From Idle Z Q, select Messages > Create Z Q 2 Z Q, use e, select User Msg. Z Q 3 Use e to select a saved message Z Q The text message can now be sent. See "Creating a Text Message" page 32. Receiving Text Messages When a Short Text Message is sent to the phone the message indicator (N) will flash in the display, with an audible tone or vibration. This indicates that a new message has been received. When Read is displayed Z Q to read the message. [. . . ] If the PUK/PUK2 is entered incorrectly 10 times, the PUK/PUK2 will be blocked. This is usually performed automatically by your phone. The ability to use your phone on networks other than your Home network. The organization responsible for providing access to the GSM network. [. . . ]