User manual PANASONIC EP-1082

[. . . ] Always insert the power plug all the way into the outlet to reduce the risk of short-circuit and fire. The unit should never be left unattended when plugged in. The unit is not to be used by people who cannot move or communicate on their own. Only use the unit for the purpose described in these instructions. [. . . ] 4 Aligntheconvexportionofthearmrestwiththe roundholeontheunit, andembedthearmreston theunit. Avoidcatchingthecoatedfabricbetween them. If it is caught, pull it out without damaging the fabric. Convex Round hole Front Rear Lift up 2 Securethearmrestswithattachment screws. Secure with screws Allen key (Total of 4 positions for a single armrest) Liftthecoatedfabriconthesideofthearmrestand inserttheattachmentscrewontotheendoftheAllen key, andthentighten. (Tighten the screws in the 4 positions lightly at first, and then tighten all screws firmly. ) *If the screw does not enter into the hole, tighten the screw by pushing the armrest from the top. 3 Closethezipperatthebottomsideof thearmrests. When closing the zipper, be careful not to twist the end of the zipper. 2 Fastenthezipper. 4 Putbothendsofthezipperintothe inside. 1 Turnintheedgeofthezipper. 2 Fixtheslidingtabofthezipperwiththevelcro. 8 5FIXTHECONTROLLERCORD Usethecontrollercordvelcroestosecurethecord, leavingapproximately18in. * Confirm that there is a margin for the controller cord length when the backrest is reclined. (The illustration shows that the cord is attached to the right armrest. ) Approx. 18 (45 cm) English 6ATTACHINGTHEBACKCUSHIONANDPILLOW 1Attachthebackcushionusingthezipper. 2Attachthepillowusingthevelcroes. FOLDINGTHEBACKRESTFORWARD(REPACKING) CAUTION · Keephands, feet, children, objects, etc. , clearofopeningsontheunit, includingseat, armrestsandlegrest;gaps betweentheunitandthefloor;andthebackrest'srangeofmovementwhenbeingfoldedforward. Failure to do so could result in injury. · Theunitshouldnotbeturnedonandthecontrolsshouldnotbeoperatedonwhenthebackrestisfoldedforward. Velcroes 10 5ADJUSTINGTHERECLININGANGLE English Press and toadjusttheangleofthebackrestandlegrest. · With the button held down, movement will continue until a "beep-beep-beep" sound indicates the backrest has been raised or lowered as far as possible. · The legrest will start to move shortly after the backrest. Approx. 120° Approx. 75° Approx. 170° Approx. 0° *The reclining operation is a function that adjusts the angle of the backrest and legrest. Avoid using it for any other purposes, such as continuous up/down operation etc. 6ADJUSTINGTHELEGRESTLENGTH Pushthelegrestoutbypullingbackonthelegrestslidelever. Pullthelegrestslidelever. Pushwiththesoles ofyourfeettoslide thelegrestout. Raisethelegsslightly andthelegrestreturns. 11 1 2Selectthepre-programyouwant. · Please press one of the flashing buttons. · If you press another Pre-Program button or a manual operation button during your selected pre-program massage, the massage will switch to the newly selected massage. · In pre-programs, the leg massage begins at the same time. It is possible to stop or change the intensity of the leg massage during the program. (See Page 13) · Pressing a Pre-Program button automatically moves the backrest and legrest into massage position. 2 3Sitasfarbackintheseataspossiblewithyourhead centeredonthepillow. 4Adjustingshoulderposition adjust the position of the · When the shoulder position indicator is flashing, massage heads (upper heads) so that they lightly touch the shoulders. Too high 4 Correct position · Lightly touching the shoulder. [. . . ] When excessive force is applied to the massage heads during operation, in the interests of safety the massage heads may stop moving. If all markings and buttons on the controller start to flash, which is extremely unusual, turn off the power switch, wait for approximately 10 seconds and then turn the power switch on again. If the massage heads stop again, position yourself so that your back is not completely in contact with the backrest. Themassageheadsdonotcomeuptotheshoulderorneck. [. . . ]