User manual PANASONIC EUR643808

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the device and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] When the program is cleared, the SET indicator flashes three times and turns off. Example: To program a consecutive procedure to watch a DVD to the SYSTEM CONTROL 2 button: Power on the DVD player. Set the input selector of the amplifier to DVD input. Set the input mode of the TV to VIDEO 1. Start DVD playback. 28 SET/SET indicator Device Select buttons 2 Enter - 8 - 1. The SET indicator flashes three times to indicate that the setting mode has been entered. 3flashes Additional Features 3 PressaSYSTEM CONTROL buttonorDeviceSelect buttonyouwantto program. , 8, 1 SYSTEM CONTROL buttons 4 Programaconsecutive procedure. With this example, press the buttons in sequence as below*: 1 PressandholdSETformore than3seconds. WhilekeepingSETheld down, press , thenrelease bothbuttons. VIDEO1 DVD TheSETindicator lightsup. * The procedure may differ depending on your device. Program the correct procedure for your device. 2 Notes You can press any button other than the SET or SYSTEM CONTROL buttons. You can skip the POWER button for Sony devices by using automatic power-on control instead. If you have programmed an incorrect operation by mistake, the setting is canceled. If you press a Device Select button in a consecutive procedure, the function already learned on the button will not be programmed. If your device does not accept consecutive remote control signals If the device does not respond to the next signal immediately after the power-on signal, you can insert other signals or an interval by pressing the same Device Select button. For Example, if TV power-on and input select do not work properly: Insert another device signal by pressing TVPOWERDVD POWERTVINPUT Insert a 0. 3 second interval between each signal by pressing TVPOWERTVINPUT (Added signals are underlined. ) Notes If you interrupt the procedure at any point for over 10 seconds, the setting mode ends. If you try to program more than 16 steps, the setting mode ends, and the 16 steps you have programmed are registered. Devices such as air conditioners, heaters, electric appliances, and electric shutters or curtains receiving an infrared signal can be dangerous if misused. Specifications Operating distance Approx. 11 m (36 ft) (varies depending on devices of different manufacturers) Two size AA (R6) dry batteries (not supplied) Approx. 1 year when using size AA (LR6) alkaline batteries (varies depending on frequency of button use - up to approx. 52 × 236 × 26 mm (2 1/8 × 9 3/8 × 1 1/16 in. ) (w × h × d) Approx. 122 g (4. 3 oz) (not including batteries) Power requirements Battery life Other Information Dimensions Mass Design and specifications are subject to change without notice. Maintenance Clean the surface with a soft cloth slightly moistened with water or a mild detergent solution. Do not use any type of solvent such as alcohol, benzene or thinner as they may damage the finish of the surface. Troubleshooting If you have problems setting up or using the EUR643808, first check the batteries (page 8), then check the items below. Symptom You cannot operate the device. Remedy Move closer to the device. The maximum operating distance is approximately 11 m (36 ft). Aim the EUR643808 directly at the device. Remove any obstacles in the path between the EUR643808 and the device. Power on the devices first, if necessary. Make sure you have pressed the correct Device Select button. [. . . ] Enters the selected item. VCR button The buttons operate as below in the factory preset mode. VCR KEY DISPLAY /// INPUT 1 ­ 9, 0 TV POWER INFO OPTIONS RECALL CH +/­ SLEEP ENTER FUNCTION Ejects a tape. DISPLAY Displays the playback information. Enables the Sleep function (when available). Enters the selected item. * These buttons correspond to TiVo service or the Replay service. [. . . ]