User manual PANASONIC EY6181

[. . . ] 2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3) Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. [. . . ] Service or maintenance performed by unqualified personnel may result in a risk of injury. 22) When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. . SPECIFIC SAFETY SPECIFIC RULES 1) Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. -3- WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks and cement and other masonry products Arsenic and chromium from chemically-treated lumber. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. 6) Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 7) An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure that: a. pins on plug of extension cord are the same number, size and shape as those of plug on charger. extension cord is properly wired and in good electrical condition. 21) Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, etc. , while charging. 22) Use of an attachment not recommend- ed may result in a risk of fire, electric shock, or injury to persons. A battery short can cause a large current flow, over heating and create the risk of fire or personal injury. 24) NOTE: If the supply cord of this appliance is damaged, it must only be replaced by a repair shop authorized by the manufacturer, because special purpose tools are required. 25) TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. . FUNCTIONAL DESCRIPTION FUNCTIONAL (A) (G) (B) (C) (D) (E) (F) (A) 6. 35 mm (1/4") hex quick connect chuck (E) Battery pack (EY9200) (B) Forward / Reverse lever (C) Variable speed control trigger (D) Bit holder (F) Battery pack release button (G) Battery charger (EY0110) -5- . ASSEMBLY ASSEMBLY Attaching or removing bit NOTE: When attaching or removing a bit, disconnect battery pack from tool or place the switch in the center position (switch lock). Hold the collar of quick connect chuck and pull it against the driver. The bit holder will return to its original position when it is released. [. . . ] Shorting the battery terminals together may cause sparks, burns or a fire. . OPERATION Switch and Forward / Reverse lever Operation (Forward ( ), Switch lock, Reverse ( )) CAUTION: Do not operate Forward/Reverse lever until the bit comes to a complete stop. -6- When operating with a Ni-MH battery pack, make sure the place is wellventilated. Battery Pack Life The rechargeable batteries have a limited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one. Charging NOTE: When you charge the battery pack for the first time, or after prolonged storage, charge it for about 24 hours to bring the battery up to full capacity. NOTE: Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety. Insert the battery pack firmly into the charger. Battry pack To AC outlet Battery charger 3. [. . . ]