User manual PANASONIC EY6813

[. . . ] Variable Speed Cordless Rotary Hammer Operating Instructions Model No: EY6813 IMPORTANT This manual contains safety information. Read manual completely before first using this product and save this manual for future use. . GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. Personal Safety 6) Stay alert, watch what you are doing, and use common sense when operating a power tool. [. . . ] Use reverse motion to loosen jammed bits. 6) When storing or carrying the tool, set the Forward/Reverse lever to the center (switch lock) position. 7) Do not strain the tool by holding the speed control trigger halfway (speed control mode) so that the motor stops. -3- 8) During charging, the charger may become slightly warm. Do not charge the battery for a long period. Symbol V meaning Volts . F O R B A T T E R Y CHARGER & BATTERY PACK 1) Direct Current n0 . . . /min no load speed revolutions or reciprocation per minutes Forward Rotation Reverse Rotation Rotation with Hammering Rotation only SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for battery charger EY0214. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. 3) CAUTION WARNING; Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: * Lead from lead-based paints * Crystalline silica from bricks and cement and other masonry products * Arsenic and chromium from chemically-treated lumber. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter the microscopic particles. To reduce the risk of injury, charge only Battery Pack shown below. EY9065, EY9066, EY9168, EY9080, EY9086, EY9182, EY9180, EY9101, EY9001, EY9006, EY9106, EY9107, EY9200, EY9201, EY9136, EY9230, EY9231, EY9117, EY9210, Other types of batteries may burst causing personal injury and damage. 4) Do not expose charger to rain or snow. 5) To reduce the risk of damaging the electric plug and cord, pull by plug rather than cord when disconnecting charger. 6) Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. -4- 7) An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. that pins on plug of extension cord are the same number, size and shape as those of plug on charger. that extension cord is properly wired and in good electrical condition. that wire size is large enough for ampere rating of charger as specified below. RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Amperes AWG Size of Cord Equal to or But less Length of Cord, Feet greater than than 25 50 100 150 0 2 18 18 18 16 15) Do not store the tool and battery pack in locations where the temperature may reach or exceed 50°C (122°F) (such a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery. 16) Do not charge battery pack when the temperature is BELOW 0°C (32°F) or ABOVE 40°C (104°F). Do not use charger in damp or wet locations. 19) The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage!Never carry charger by cord or yank it to disconnect from outlet. [. . . ] Metal drill Metal hole saw for wood drill with high torque. 90 minutes. ) If a fully charged battery pack is inserted into the charger again, the charging lamp may light up. After several minutes, the charging lamp may flash quickly to indicate the charging is completed. 6. If the charging lamp does not light immediately after the charger is plugged in, or if after the standard charging time the lamp does not go off, consult an authorized dealer. [. . . ]