User manual PANASONIC EY7202GQW

[. . . ] Before operating this unit, please read these instructions completely and save this manual for future use. 35 mm (1/4") hex quick connect chuck 6, 35 mm (1/4") Sechskant-Schnellaufspannfutter Mandrin de connexion rapide hexagonal de 6, 35 mm (1/4") Mandrino esagonale di collegamento rapido da 6, 35 mm (1/4") 6, 35 mm zeskantboorkop met snelkoppeling Mandril hexagonal de conexión rápida de 6, 35 mm (1/4") 6, 35 mm (1/4") hexagonal borepatron til hurtig tilslutning Snabbchuck med 6, 35 mm sexkantshylsa 6, 35 mm (1/4") hex hurtigtilkoplingschuck 6, 35 mm (1/4") kuusiopikaistukka 6, 35 (1/4") 6, 35 (1/4") Belt hook lock lever Riemenhaken-Verriegelungshebel Levier de verrouillage du crochet de ceinture Leva di blocco gancio da cintura Borghendel voor riemclip Palanca de bloqueo del gancho de cinturón Låsehåndtag til bæltekrog Låsknapp för bälteskrok Låsespak for beltekrok Vyölenkin lukitusvipu Battery pack (EY9201) Akku (EY9201) Batterie autonome (EY9201) Pacco batteria (EY9201) Accu (EY9201) Batería (EY9201) Batteripakning (EY9201) Batteri (EY9201) Batteripakke (EY9201) Akku (EY9201) (EY9201) (EY9201) Impact power mode button Schlagkraftmodustaste Bouton de mode de puissance d'impact Tasto modalità potenza impatto Slagkracht-functietoets Botón de modo de potencia de impacto Slagkraftfunktionsknap Slagkraftsväljare Innstillingsknapp for slagstyrke Iskutehomuodon painike Variable speed control trigger Elektronikschalter Gâchette de commande de vitesse Grilletto di controllo velocità variabile Startschakelaar met variabele toerentalregeling Disparador del control de velocidad variable Kontroludløser for variabel hastighed Avtryckare med variabel varvtalsreglering Hovedbryter, trinnløs Nopeudensäätökytkin Read "the Safety Instructions" booklet and the following before using. 1) Be aware that this tool is always in an operating condition, since it does not have to be plugged into an electrical outlet. Hold the tool only by the plastic handle to prevent electric shock in case you screw or drive into a "live" wire. [. . . ] The driver is preset to "hard" impact mode setting when shipped from the manufacturer. When maximum power is required in each impact mode, set the clutch to the "F" mode. Fastening small diameter screws into hard materials. Driving machine screws when installing devices. Indication lights on the control panel The indication lights will go off in the following cases. Depressing the trigger switch again, then indication lights go on in the previous condition. This function helps adjust the screw head flush to the material surface. The driver rotates half round and automatically stops each time the trigger switch is depressed while tightening a screw. The driver will give impact about 5 times and automatically stop while tightening a bolt even though the trigger switch is depressed. The digital clutch automatically stops the driver rotation when the load is reached to the select setting. depress the trigger switch fully to tighten the screws until the digital clutch operates. If the screw head is not flush to the material surface, release the trigger switch and then within 1 sec. ) Press the impact power mode button to set the impact power mode. Over-tightening may occur when tightening screws into soft materials as the tool does not impact. When the trigger switch is released and it is depressed fully within 1 sec. Then the one-shot impact LED light will blink. After trigger is released, not to operate the one-shot impact function. Keeping the bit head to the screw head to use this function. When the screw is sticking up quite a ways, increase the clutch setting. (Digital Full power clutch is turned off in the each impact power mode. To set the one-shot impact function, press the button () then light () turns on. Depress the trigger switch fully to adjust the screw tightening until the one-shot impact function operates. [. . . ] 7) Effect of Connecting Adaptor The tightening torque will be lowered through the use of a universal joint or a connecting adaptor. Use only bits suitable for size of chuck. Model Screw driving Wood screw Self-drilling screw EY7202 3. 5 - 6 mm (1/8" - 1/4") Standard bolt : M6 - M12 High tensile bolt : M6 - M10 Impact power Clutch setting stage reference mode H M S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 When screwing TEKS screws into hard materials, use the lighter digital clutch's setting to avoid slippage which may chip or damage the screw. [. . . ]