User manual PANASONIC FP-7735

[. . . ] Should the fuse need to be replaced, a BSI or ASTA approved fuse and of the same rating as the one removed from the plug must to BS1362 marked or be used. Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below. [. . . ] Do not subject the machine to shock or vibration. In particular, never move the machine while the power is on. 30 cm (11-13/16") 30 cm (11-13/16") 45 cm (17-23/32") A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health hazard. NOTE: The present recommended long term exposure limit for ozone is 0. 1 ppm (0. 2 mg/m3) calculated as an 8 hr. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area. 4 SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. Be sure to use only PANASONIC-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher staple cartridge, and transparency film. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of Sharp products. Look for the Genuine Supplies label on the toner package. GENUINE SUPPLIES Storage of supplies Proper storage 1. Store the supplies in a location that is: · clean and dry, · at a stable temperature, · not exposed to direct sunlight. Store paper in the wrapper and lying flat. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds. Storing toner cartridges Store a new toner cartridge box horizontally. length 800 mm (31-31/64"), scanning in mono 2 mode of one side only is possible in fax and image scan modes. ) One-sided 35 g/m2 to 128 g/m2 (9 lbs. to 34 lbs. ) (Paper weights from 35 g/m2 (9 lbs. ) to 49 g/m2 (13 lbs. ) require the use of slow scan mode. ) Two-sided 50g/m2 to 105 g/m2. to 28 lbs. ) 100 sheets (80 g/m2 (21 lbs. )) Maximum stack height of 13 mm (1/2") Supplied from the machine Original weight Capacity Power supply Exit tray unit (right tray) specifications Model Output method Output capacity* Dimensions Weight MX-TRX1 Face-down output 100 sheets (using PANASONIC-recommended A4 or 8-1/2" x 11" paper) When tray is folded up: 289 mm (W) x 405 mm (D) x 52 mm (H) (11-3/8" (W) x 15-61/64" (D) x 2-3/64" (H)) When tray is extended: 419 mm (W) x 405 mm (D) x 52 mm (H) (16-1/2" (W) x 15-61/64" (D) x 2-3/64" (H)) Approx. 0. 93 kg (2 lbs. ) * The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of paper, and the storage conditions of the paper. 9 SPECIFICATIONS Stand/1x500 sheet paper drawer specifications Model Paper sizes Paper weight Paper capacity Paper types Automatic paper size detection Power supply Dimensions Weight MX-DEX1 A3, B4, A4, A4R, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16K, 16KR Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs. )) 500 sheets (80 g/m2 (21 lbs. )) x 1 tray PANASONIC-recommended plain paper, recycled paper, and coloured paper When "Auto-AB" automatic detection is selected: A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13") When "Auto-Inch" detection is selected: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R Supplied from the machine 720 mm (W) x 670 mm (D) x 303 mm (H) (28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H)) (including adjuster) Approx. 20 kg (44. 1 lbs. ) Stand/2x500 sheet paper drawer specifications Model Paper sizes Paper weight Paper capacity Paper types Automatic paper size detection Power supply Dimensions Weight MX-DEX2 A3, B4, A4, A4R, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 8K, 16K, 16KR Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs. )) 500 sheets (80 g/m2 (21 lbs. )) x 2 trays PANASONIC-recommended plain paper, recycled paper, and coloured paper When "Auto-AB" detection is selected: A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13") When "Auto-Inch" detection is selected: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R Supplied from the machine 720 mm (W) x 670 mm (D) x 303 mm (H) (28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H)) (including adjuster) Approx. (51. 8 lbs. ) 10 SPECIFICATIONS Large capacity tray specifications* Model Paper sizes Paper weight Paper capacity Paper types Power supply Dimensions Weight MX-LCX1 A4, 8-1/2" x 11" (paper size change must be performed by a service technician) Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs. )) 3500 sheets (80 g/m2 (21 lbs. )) PANASONIC-recommended plain paper, recycled paper and coloured paper Supplied from the machine 370 mm (W) x 550 mm (D) x 520 mm (H) (14-9/16" (W) x 21-21/32" (D) x 20-15/32" (H)) Approx. 29 kg (63. 9 lbs. ) * Stand/1x500 sheet paper drawer (MX-DEX1) or stand/2x500 sheet paper drawer (MX-DEX2) is required. 11 SPECIFICATIONS Finisher specifications Model Paper sizes Paper weight Modes MX-FNX1 A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs. )) Plain paper (60 g/m2 to 105 g/m2 (16 lbs. [. . . ] · IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation. · Sharpdesk is a trademark of Sharp Corporation. · All other trademarks and copyrights are the property of their respective owners. Candid and Taffy are trademarks of Monotype Imaging, Inc. [. . . ]