User manual PANASONIC FV-08VKML1

[. . . ] Ventilating Fan Model No. FV-08VKML1 FV-08VKSL1 FV-08VKML1 FV-08VKSL1 R READ AND SAVE THESE INSTRUCTIONS. Thank you very much for having purchased our Ventilating Fan. Please read these instructions carefully before attempting to install, operate or service the Panasonic Ventilating Fan. Failure to comply with instructions could result in personal injury and/or property damage. Please retain this booklet for future reference. Table of Contents Please Read Prior To Installing This Fan Unpacking Supplied Accessories Description Dimensions Wiring Diagram Switch Indication Operation Specifications General Safety Information Installation I ( Joist Mounting-I ) Installation II ( Joist Mounting-II ) Installation III ( I-Joist Mounting ) Installation IV ( Between Joist Mounting ) Installation V ( Wooden Header ) Installation VI ( In Existing Construction ) Maintenance Practical Guide to Installation Product Service 2 3 3 3 4 5 5 6 6 7 8-10 11-12 12 13 14 14 15-16 16 16 ventilating 5 FV-08VKSL1 FV-08VKML1 only). efficient than the minimum ENERGY STAR requirements. UNPACKING Unpack and carefully remove unit from carton. [. . . ] (Fig. 4) Junction box cover Circular duct Conduit Joist 5. Follow all the local electrical safety codes. As well as the National Electrical Code (NEC). Using UL approved wire nuts, connect house power wires to ventilating fan wires: black to black; white to white; green to green; Connect the two red wires to the switch for the speed control. (Fig. 4) Duct tape CAUTION: Mount junction box cover carefully so that lead wires are not pinched. Install a circular duct and secure it with duct tape or clamps. Junction box Conduit Junction box Conduit Green wires Green wires Lead wires Wire nut Red wires Lead wires Wire nut Fig. 4 9 INSTALLATION I ( JOIST MOUNTING- I ) CONTINUED 7. Ceiling hole should be aligned with the edge of the flange. (Fig. 5) 10 7/8 (27 5) 10 7/8 (27 5) Ceiling 8. Insert the plug connector II into the receptacle II , and secure the lighting unit to the fan body with 1 screw III (ST4. 2X16) and 2 machine screws (M4X8). (Fig. 5) Lighting unit Machine screw (M4X8) 9. Insert the fluorescent lamps and secure the night lamp into the lighting unit. (Fig. 5) Machine screw (M4X8) Screw III (ST4. 2X16) Plug connector II Fluorescent lamps inches (mm) 4 W Night lamp Fig. 5 10. Insert mounting spring into the slot as shown and adjust high /low delay time preset switch and low speed air volume preset switch. Refer to switch indication of page 5 (FV-08VKML1) (Fig. 6-1) Ceiling Grille Lighting unit Sensor unit Fig. 6-1 11. Insert the sensor unit into the housing of the grille and insert other mounting spring into the slot as shown and mount grille to fan body (FV-08VKML1) (Fig. 6-2, Fig. 6-3) Ceiling Grille Sensor unit Gloves Fig. 6-2 CAUTION: Mount grille carefully so that lead wires are not pinched. Ceiling Mounting spring Grille Gloves Fig. 6-3 12. Insert mounting springs into the slots as shown and mount grille to fan body. (FV-08VKSL1) (Fig. 7) Slot Lighting unit Mounting spring Ceiling Gloves Grille Fig. 7 10 INSTALLATION II ( JOIST MOUNTING- II ) 1. Remove the machine screw by using screw driver, disconnect plug connector from receptacle and remove adaptor from fan body before installation. Before installation, secure the lighting unit to fan body (refering to Fig. 5 of page 10). Connect the suspension bracket III to fan body. (Fig. 13) (Select the hole by checking I-joist size and fix the screw to the frame hole. ) 3. Follow steps 4 to 12 of installation I (page 9, page 10) to complete the installation work. 4 Long screws (ST4. 2X20) I- joist Fig. 14 12 INSTALLATION IV ( BETWEEN JOIST MOUNTING ) 1. [. . . ] Remove sensor unit then pull down the other mounting spring. (Squeeze mounting spring and pull down carefully. ) (Fig. 21) 2. (Use non-abrasive kitchen detergent, wipe dry with new cloth. ) (Fig. 22) Fig. 21-2 Glove Fig. 22 3. The grille should be dry after cleaning. [. . . ]