User manual PANASONIC FV-11VH1

[. . . ] Spot and Continuous Ventilation: These fans are designed to run continuously ensuring a healthy environment at low CFM levels 24 hours a day. By utilizing a pre-set lower level(0, 30, 40, 50, 60, 70 CFM). The setting is dependent on the size of the room and the individual wishes of the homeowner. (Sq. feet) <1, 000 1, 500 2, 000 2, 500 3, 000 Two Bedrooms Three Bedrooms 33 38 43 48 53 40 45 50 55 60 Four Bedrooms 48 53 58 63 68 Five Bedrooms 55 60 65 70 75 These fans are also built to take care of the homeowner's spot ventilation needs when the room is occupied. These models kick-up to a maximum level of 80 CFM either when the switch is turned on(FV-08VKSL2)or activated by the A High/Low Delay Timer, Iocated inside the fan body, is utilized to return the fan back to the Pre-set continuous ventilation mode. factors increase static pressure hindering the performance of most ventilation fans. These fans utilize microchip technology that monitors the static pressure in the system and speeds up or slows down the rpm of the fan depending on the amount of resistance. This allows the fan to perform as rated, whether facing 0. 1, 0. 2 or even 0. 25 inches water gauge. The bottom line is that it makes for easier installation. The installer no longer has to worry about compromising the fan's performance. technology. The new DC motor is 30%-70%more energy efficient than the minimum ENERGY STAR requirements. This product contains electronic ballast with fluorescent lamps and is in compliance with Part 18 of the FCC rules as consumer RF lighting device. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0. 45-30 MHz. If interference should occur, try to increase spacing between this product and other product. [. . . ] Do not use this unit with any solid-state control device. Solid state controls may cause harmonic distortion which can cause motor humming noise. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally, When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. If this unit to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI(Ground Fault Circuit Interrupter)-protected branch circuit. Not to be installed in a ceiling thermally insulated to a value greater than R40. (This is required for installation in Canada only. ) 7 INSTALLATION IMPORTANT: (JOIST MOUNTING- ) Remove the tape from damper and adaptor before installation. As shown below: Adaptor Damper Suspension Tape bracket I Fan body Fig. 1-1 1. Insert the suspension bracket into the fan body and adaptor. (Select the suspension bracket as shown below. ) Suspension Joists bracket I Fan body Suspension bracket III Fig. 1-2 Spacing A on center joists Insert Suspension bracket 12 inches 16 inches 19. 2 inches vertical joists 24 inches Refer to Fig. 1-4 Suspension bracket III Suspension bracket I If spacing A on center joists is 24 inches, connect suspension bracket II and III (C4 mark to C4 mark) as shown below: 2-Screw I (ST4. 2X8) Suspension bracket II Suspension bracket III Fan body Fig. 1-3 Suspension bracket III Suspension bracket II Suspension bracket I Fan body Fig. 1-4 8 INSTALLATION (JOIST MOUNTING- ) CONTINUED Joist 2. Install the suspension bracket and the flange of fan body to joists by using long screws (ST4. 2X20) (If spacing A between joists is 12 inches, install the flange of fan body according to Fig. 2-1, others according to Fig. 2-2 to install the product) Fan body 2 Long screws (ST4. 2X20) Fig. 2-1 Joist Fan body 4 Long screws (ST4. 2X20) Fig. 2-2 Joist 3. Install the suspension bracket to joists by using long screws (ST4. 2X20) and secure it to the fan body by using screw II (ST4. 2X12) (Fig. 3) 2 Long screws (ST4. 2X20) Screws II (ST4. 2X12) Circular duct Fig. 3 4. Remove junction box cover and secure conduit or stress relief to junction box knock-out hole. (Fig. 16) If installing with fan body flange below drywall, keep the distance B (1/ 2 inch, 12. 7mm or 5/8 inch, 15. 9mm) for the thickness of ceiling board. Suspension bracket II Fig. 15-2 Joists Adaptor Fan body Junction box 13 1/4~15 3/4 (336~400) 16 1/2~18 3/4 (419~480) 3~ 5 5 4/5~7 4/5 ( 76~126) (148~198) Inches(mm) 1/2 (12. 7) 5/8 (15. 9) Fig. 16 4. Secure the suspension bracket to joists by using long screws (ST4. 2X20) (Fig. 17, Fig. 18) 2 Long screws (ST4. 2X20) 5. Secure the suspension bracket to fan body by using screw II (ST4. 2X12) (Fig. 18) Fig. 17 2 Screw II (ST4. 2X12) 4 Long screws (ST4. 2X20) 6. Follow steps 4 to 12 of installation I (page 9, page 10) to complete the installation work. Joist Fig. 18 13 INSTALLATION ( WOODEN HEADER ) Joist Header 1. Before installation, secure the lighting unit to fan body (refering to Fig. 5 of page 10). Install header between joists by using nails or screws. Joist Adaptor Fan body Inches (mm) Adaptor Fig. 19 3. Install the fan body and secure it by using long screws(ST4. 2X20) (Fig. 19, Fig. 20) Circular duct 4. Follow steps 4 to 12 of installation I (page 9, page 10) to complete the installation work. 6 Long screws (ST4. 2X20) Fig. 20 INSTALLATION (IN EXISTING CONSTRUCTION ) 1. Installing the fan body in an existing building requires an accessible area (attic or crawl space) above the planned installation location or existing ducting and wiring. (1) To install the fan body, follow the procedures described in Installation II. Take the following precautions before installation. CAUTION: Check area above planned installation location to be sure that: 1. [. . . ] Remove grille pull down one mounting spring. Remove sensor unit then pull down the other mounting spring. (Squeeze mounting spring and pull down carefully. ) (Fig. 21-1, 21-2) 2. (Use non-abrasive kitchen detergent, wipe dry with new cloth. ) (Fig. 22) Ceiling Grille Sensor unit Gloves Fig. 21-2 Gloves Fig. 22 3. [. . . ]