User manual PANASONIC GP-KS162CUD

[. . . ] Nous déclarons sous note seule responsabilité que le produit auquel se réfère la présente déclaration est conforme aux normes ou autres documents normatifs conformément aux dispositions des directives 2006/95/CE et 2004/108/CE. Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia esta declaración está conforme con las normas u otros documentos normativos siguiendo las estipulaciones de las directivas 2006/95/CE y 2004/108/CE. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme ai seguenti standard o altri documenti normativi conformi alle disposizioni delle direttive 2006/95/CE e 2004/108/CE. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 2006/95/EC en 2004/108/EC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 2006/95/EC og 2004/108/EC. [. . . ] Toggles the dynamic range between NORMAL and EXPAND. Specifies the level of the digital noise reduction function. Page 17 w e r t y u i o !0 !1 !2 ELC SHUTTER GAIN SENS UP OUTPUT SEL SCENE FILE DTL MODE RED DTL GAMMA KNEE BLACK STRETCH D-RANGE WHITE CLIP FLARE COMP DNR MATRIX CHROMA GAIN TOTAL PED WHITE BAL BLACK BAL SYNC ELECTRIC ZOOM FREEZE 18 19 19 19 19 20 20 20 20 21 21 21 21 21 21 21 22 22 23 23 24 24 24 15 s Basic operations The description below explains how to operate the SETUP menu basically. First of all, the explanation provides how to display the SETUP menu on the connected monitor used for adjustment. v To return to the camera image screen after storing the settings, move the cursor to "END" and press the [SEL] button. The settings can be stored even if the power of the CCU is turned off. Important: · The following functions are not available when the camera head is not connected. · Startup of white balance AWC · MATRIX · ELECTRIC ZOOM · FREEZE Top screen of SETUP menu ** SET UP ** CAMERA ID ELC SHUTTER GAIN SENS UP OUTPUT SEL END P1 *OFF *OFF OFF OFF OFF RGB(NOR) ** SET UP ** P2 SCENE FILE *FILE1 WHITE BAL AWC BLACK BAL *MANU SYNC INT ELECTRIC ZOOM ON FREEZE ON END z Hold down the [FREEZE (MENU)] button for approx. The top screen of the SETUP menu appears. x The SETUP menu consists of 2 pages. To change the page, move the cursor to "P1" or "P2" and press the [e] or [f] button. Note: · The cursor is a blinking part. c Perform the settings for each item. · Selection of setting item: Press the [g] button or the [h] button to move the cursor. · Change of settings: Press the [e] button or the [f] button. · Display of advanced setup screen: Press the [SEL] button when "*" is attached to the target setting item. · Return to previous setup screen: Move the cursor to "RET" and press the [SEL] button. 16 1. The area is selectable from the types shown below. The detection areas shown as follows are not displayed. ALL (default): All of the areas on the screen are the detection area. S CIRCLE: The small circle in the center of the screen is the detection area. z Select "MANU" for "AREA" on the "ELC CONT" screen and press the [SEL] button. the [g], [h], [e], and [f] buttons to select an area to be masked and press the [SEL] button. Note: · To cancel the specified area, move the cursor to the target area and press the [SEL] button. To cancel all the masks, hold down the [e] and [f] buttons simultaneously for more than 2 seconds. x Use M CIRCLE: The medium circle in the center of the screen is the detection area. c Hold down the [MENU] button for more than 2 seconds after area setting. The "ELC CONT" screen appears again. L CIRCLE: The large circle in the center of the screen is the detection area. 18 3. Electronic shutter setting [SHUTTER] The electronic shutter speed is specified. The speed is selectable from the following. OFF (default), 1/100 (1/120*), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, and MANU Select "MANU", and press [SEL] button. [. . . ] Check whether the monitor settings are appropriate. -- Camera with no response to the button operation on the front face of the CCU · Is the function setup switch No. 11 The lighting LED of the [SCENE] button unchanged · Pressing once displays the state. Press the [SCENE] button repeatedly until your target LED lights. 9 The lighting LED of the [GAIN] button unchanged · Pressing once displays the state. Press the [GAIN] button repeatedly until your target LED lights. 9 Only the color bar displayed · Is the camera cable appropriately connected at both the connector of the CCU and the connector of the camera head? [. . . ]