User manual PANASONIC GP-KS822CU

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] The preset 1, preset 2 and automatic setting mode are provided for Light Measurement Area Selection. 2 m {6. 6 ft. } and 3. 8 m {12. 5 ft. } cable length between camera head and camera control unit with optional camera cable. S-VHS Video Output is provided. -5- PRECAUTIONS · Do not attempt to disassemble the camera. To prevent electric shock, do not remove screws or cover. There are no user-serviceable parts inside. Refer servicing to qualified service personnel. · How to take care of this camera. After turning OFF the DC power switch, clean it with a dry cloth. If it is difficult to remove the dirt or dust, clean it up with a cloth applied the neutral cleanser. Use the lens cleaning tissue paper(may be available at your local camera store) for lens cleaning. · Do not expose the camera or camera control unit to rain or moisture, or do not try to operate it in wet areas. Do take immediate action if ever the camera or camera control unit do become wet. Turn power off and refer servicing to qualified service personnel. Moisture can damage the camera and camera control unit and also create the danger of electric shock. · Connect this to a DC 12 V, min. 600 mA CLASS 2 Power supply only. · After using the camera, turn OFF the DC power switch and put the lens cap on the camera head. · Ambient Temperature range Do not install the camera in the place which is beyond 10 °C to 45 °C {50 °F to 113 °F}. · Every necessary procedures with regard to install this product should be made by qualified service personnel or system installers. · Do not drop anything inside the camera. Dropping metal for example inside the camera could permanently damage the unit. · Never crush or pinch the camera cable. Do not bend the camera cable into a curve whose radius is too small. Caution: Connecting or disconnecting camera cable to/from the camera control unit must be done after turning OFF the DC power switch. Otherwise, the camera head may be damaged. · Whether the camera is in use or not, never face it toward the sun. Do use caution when operating the camera in the vicinity of spot lights or other lights and light reflecting objects. · Do not loosen the chassis of the camera head. · Do not connect Panasonic GP-KS162CU and GP-KS822H, nor GP-KS822CU and GP-KS162H. -6- SYSTEM BLOCK DIAGRAM GP-KS822 Standard Configuration Camera Head, Tripod Attachment, Camera Control Unit. Optional Camera Cable GP-CA162/2: 2 m GP-CA162/38: 3. 8 m FOCUS LOCK GP-KS822H ON OFF DC POWER AWC ATW MANU WHITE BAL. IMAGE ORIENT. AUTO MANU ROTA. BRIGHTNESS GP-KS822 NORM. START R B LIVE/FREEZE CAMERA Camera Head (GP-KS822H) Camera Control Unit GP-KS822CU Optional Accessories Wide Angle Lens GP-LM3TA Wide Angle Lens GP-LM7TA Pinhole Lens GP-LP12TA Tele Angle Lens GP-LM15TA C-Mount Adaptor GP-AD22TA Tele Angle Lens GP-LM24TA MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Camera Control Unit GP-KS822CU !5!7!9@1 q we r WHITE BAL. AWC ATW MANU !3 !1 y IMAGE ORIENT. [. . . ] Mount the Pinhole Lens, Wide-angle Lens or Super Wideangle Lens to the camera by rotating it clockwise slowly. 3. Rotate the focus lock ring fully Mount the lens and C-mount adaptor by rotating them clockwise slowly. Focus Lock Ring Focus Lock Ring Caution: If the optional C-mount lens size exceeds 50. 8 mm {2"} in diameter, 70 mm {2-3/4"} in length and 300 g {0. 66 lbs} in weight, both the camera and lens should be secured. -10- SPECIFICATIONS Pick-up Device : Horizontal Resolution : Minimum Scene Illumination : Signal to Noise Ratio : Video Output : Scanning System : Synchronization : White Balance : AGC: ELC: Brightness: Light Measurement Area: Image Orientation: Freeze: Aperture Compensation: Function Switches: For NTSC : 1/2-inch Interline transfer CCD image sensor with 768 (H) x 494 (V) pixels For PAL : 1/2-inch Interline transfer CCD image sensor with 752 (H) x 582 (V) pixels 480 lines 6 lx {0. 6 footcandles} (F1. 4 with AGC ON more than 30 IRE of Y signal with set up) 50 dB (Standard condition, Y signal) 1. 0 V[P-P]/75 , composite video, BNC connector x 2) 2:1 Interlace Internal Sync only Auto Tracing White Balance(ATW)/Auto White Balance Control(AWC)/Manual(MANU) ON/OFF (Approx. 12 dB gain at AGC on position) ON/OFF MANUAL/AUTO FULL/PRESET1/PRESET2/AUTO NORMAL/ROTATE or NORMAL/MIRROR FREEZE/LIVE HIGH/LOW Auto White Balance Control Button White Balance Selection Switch (AWC/ATW/MANU (Manual)) Image Orientation Selection Switch (NORM. (Rotate)) Brightness Selection Switch (AUTO/MANU (Manual)) Live/Freeze Button ELC On/Off Switch AGC On/Off Switch 2-Memory AWC Mode On/Off Switch Mirror/Rotate Selection Switch Light Measurement Area Selection Switch Aperture Level Selection Switch Cable Selection Switch White Balance R/B Gain Control Brightness Control 12 V DC, 450 mA GP-CA162/2 Cable 2 m {6. 6 ft. } GP-CA162/38 Cable 3. 8 m {12. 5 ft. } 10 °C to 45 °C {50 °F to 113 °F} Camera Head : 17 (Diameter) x 35. 5 (D) mm {2/3" (Diameter) x 1-1/2"(D)} Camera Control Unit : 120 (W) x 36 (H) x 157 (D) mm {4-11/16" (W) x 1-7/16" (H) x 6-1/8" (D)} Camera Head : 14 g {0. 035 lbs} Camera Control Unit : 530 g {1. 2 lbs} Controls: Power Source : Camera Cable Length : Ambient Temperature : Dimensions : Weight : Weight and dimensions indicated are approximate. [. . . ]