User manual PANASONIC GP-MF130

[. . . ] Whether the camera is in use or not, never aim at the sun or other extremely bright objects. Otherwise, blooming or smear may be caused. GP-MF130 7. Dropping metal for example inside the camera could permanently damage the unit. [. . . ] If anything is dropped inside the camera, turn the power off immediately and ask a qualified service person for servicing. Do not operate the camera beyond the specified temperature, humidity or power source ratings. Use the camera under conditions where temperature is between -10°C - +50°C (14°F 122°F), and humidity is below 90 %. The input power source is DC 12 V, 465 mA. Before attempting to connect or operate this product, please read these instructions completely. MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS N1098-0 YWV8QA5088AN Printed in Japan N 30 t r y i o !0 !1 u CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Remove dust on the faceplate of filter glass before mounting the lens on the camera. For U. S. A ON 12345678 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. SA 1965 The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, i. e. , in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. q VIDEO w e The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. For setting the Rear Panel Switch No. 1 to 8, remove the switch cover fixing screw on the rear panel as shown below. Pick-up Device : Image Size : Synchronization : Inter Line Transfer type CCD with 768 (H) x 494 (V) pixels. 2/3" (7. 95 (H) x 6. 45 (V) mm) Full non interlace (1/60 s) Internal or External (Selectable Automatically) Internal : Built-in sync generator External : 4. 0 V[p-p]/75 Horizontal drive and Vertical drive pulses External signal (4. 0 V[p-p]/75 , negative) supplied to EXT VD IN connector can be used as reset signal 500 lines at center 5 lx (0. 5 foot-candles), (F1. 4, Gain (+6 dB) , OFF) 1. 0 0/+6 dB 9-step (1/100 s to 1/30 000 s) at normal 5-step (1/2 000 s to 1/30 000 s) at Shutter Trigger C-Mount 7 G (10 Hz - 150 Hz) (2 hours each for three axes) 80 G (IEC 68) *IEC=International Electronical Technical Commission DC + 12 V, 465 mA -10°C - +50°C (14°F - 122°F) 45(W) x 45(H) x 120(D) mm [1-25/32"(W) x 1-25/32"(H) x 4-23/32"(D)] 270 g (0. 6 lbs. ) (Camera Only) 2. Lenses Be sure to use the optional manual iris lens having the following items. Focus : Adjustable Lens Weight : Less than 300 g (0. 66 lbs. ) Note: If the lens is heavier than 300 g (0. 66 lbs. ), both the lens and the camera should be secured by using the supporter. Mount : C-mount The protrusion at the rear of the lens should be as shown in the illustration. External Reset : Horizontal Resolution : Minimum Illumination : Gamma : Gain Selection : Electronic Shutter : Lens Mount : Vibration Resistance : Shock Resistance : Power Source : Ambient Temperature : Dimensions : Weight : Remove this screw VIDEO Dimensions and weight indicated are approximate values. Specifications are subject to change without notice. Less than 7. 5 mm (1/2") SYSTEM CONNECTIONS Caution: Keep the power switches of all units to OFF before connections. Connect the optional camera cable GP-CA34 between the connector of this camera and the 12 V DC Class 2 power supply(not provided as an accessory). [. . . ] Specifications are subject to change without notice. Less than 7. 5 mm (1/2") SYSTEM CONNECTIONS Caution: Keep the power switches of all units to OFF before connections. Connect the optional camera cable GP-CA34 between the connector of this camera and the 12 V DC Class 2 power supply(not provided as an accessory). Connect the video connector of the GP-CA34 to the Frame Grabber. OPTIONAL ACCESSORIES Camera Cable GP-CA34 GP-CA33 GP-CA59 GP-CA60 Camera GP-CA34 Video input of Frame Grabber 12V DC Power Supply HD IN VD/V reset Caution: Use a 12 V DC Class 2 Power Supply only EXTERNAL SYNCHRONIZATION Full non interlace The GP-MF130 works in full non interlace mode when external HD/VD signal is supplied to pin-6 and pin-7 of the camera connector (12-pin). [. . . ]