User manual PANASONIC HF-S45150E

[. . . ] ‰¥ Four ThirdsTM and Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. ≥ G MICRO SYSTEM is an interchangeable lens type digital camera system of LUMIX based on a Micro Four Thirds System standard. ‰¥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned. Book 3 ページ ２０１２年８月８日　水曜日　午後４時５０分 ENGLISH -If you see this symbol- Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. [. . . ] 1 Lens Hood 2 Lens Cap 3 Lens Rear Cap (The lens rear cap and lens cap are attached to the interchangeable lens at the time of purchase. ) • Do not press the lens release button C when you attach a lens. €¢ Do not try to attach the lens when holding it at an angle to the camera body as the lens mount may get scratched. Book 6 ページ ２０１２年８月８日　水曜日　午後４時５０分 ∫Detaching the Lens ≥ Check that the camera is turned off. ˆ« Attaching the Lens Hood (Supplied Accessory) 1 Align the fitting mark E on the lens hood with the mark on the tip of the lens. 2 Turn the lens hood in the direction of the arrow until it stops, and align the stop mark F on the lens hood with the mark on the tip of the lens. While pressing on the lens release button D, rotate the lens toward the arrow until it stops and then remove. €¢ Attach the lens rear cap so that the lens contact point does not get scratched. €¢ Attach the body cap to the camera so no dirt or dust will get inside the main unit. ˆ«Attaching and Detaching the Lens Cap Pinch the lens cap as shown in the figure to attach or detach. ‰¥ Be careful not to lose the lens cap. Book 7 ページ ２０１２年８月８日　水曜日　午後４時５０分 ∫ Temporarily Storing the Lens Hood 1 Turn the lens hood in the direction of the arrow to detach it. ˆ« Attaching Filters ≥ Vignetting may occur if using 2 or more MC protectors (optional: DMW-LMC52), PL filters (optional: DMW-LPL52) or ND filters (optional: DMW-LND52), or if using thick protectors and/or filters. ‰¥ The filter may become impossible to remove if excessively tightened, so please refrain from tightening it too strongly. ‰¥ It is possible to attach the lens cap with the filter already attached. ‰¥ You cannot attach a conversion lens or adaptor to this lens. A filter may be used, but attaching any other element may cause damage to the lens. 2 Reverse the lens hood and then attach it in the same way as shown previously. ‰¥ When taking pictures with the flash with the lens hood attached, the lower portion of the screen may turn dark (vignetting effect) and the control of the flash may be disabled because the photo flash may be obscured by the lens hood. ‰¥ When using the AF assist lamp in the dark, detach the lens hood. Book 8 ページ ２０１２年８月８日　水曜日　午後４時５０分 Names and Functions of Components Note ≥ When flash recording with a close subject, the light of the flash will be blocked by the lens and part of the picture may be dark. Check the distance from the subject when recording. [. . . ] When this lens is attached to digital camera, stabilizer function cannot be turned off or stabilizer function does not work. ‰¥ The Optical Image Stabilizer function of this lens only works correctly with supported cameras. > When older Panasonic digital cameras (DMC-GF1, DMC-GH1, DMC-G1) are used, [Stabilizer] in the [Rec] mode menu cannot be set to [OFF]. It is recommended to update the firmware of the digital camera at the following website. [. . . ]