User manual PANASONIC HH014AE

[. . . ] ‰¥ Four ThirdsTM and Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. ≥ G MICRO SYSTEM is an interchangeable lens type digital camera system of LUMIX based on a Micro Four Thirds System standard. ‰¥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned. Book 3 ページ ２０１４年８月１８日　月曜日　午後４時２９分 ENGLISH -If you see this symbol- Disposal of Old Equipment Only for European Union and countries with recycling systems This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste. [. . . ] product numbers correct as of August 2014. 1 2 SYF0001 VFC4605 1 Lens Cap 2 Lens Rear Cap (The lens rear cap and lens cap are attached to the interchangeable lens at the time of purchase. Book 6 ページ ２０１４年８月１８日　月曜日　午後４時２９分 Names and Functions of Components 1 Lens surface 2 Focus ring Rotate to focus when taking pictures with manual focus. 3 Contact points 4 Lens fitting mark 4 1 2 3 6 SQT0455 SQT0455_E. Book 7 ページ ２０１４年８月１８日　月曜日　午後４時２９分 Attaching/Detaching the Lens ≥ Refer also to the camera’s operating instructions for attaching and detaching the lens. ˆ« Detaching the Lens ≥ Check that the camera is turned off. ˆ« Attaching the Lens ≥ Check that the camera is turned off. A: Lens Rear Cap Press the lens release button C while turning the lens as far as possible in the direction of the arrow to detach it. €¢ Attach the lens rear cap so that the lens contact point does not get scratched. €¢ Attach the body cap to the camera so no dirt or dust will get inside the main unit. 2 Align the lens fitting marks B on the camera body and the lens and then rotate the lens in the direction of the arrow until it clicks. €¢ Do not press the lens release button C when you attach a lens. €¢ Do not try to attach the lens when holding it at an angle to the camera body as the lens mount may get scratched. • Check that the lens is attached correctly. €¢ Be sure to remove the lens cap when recording. Book 8 ページ ２０１４年８月１８日　月曜日　午後４時２９分 ∫Attaching Filters ≥ Vignetting may occur if using 2 or more MC protectors (optional: DMW-LMC46), PL filters (optional: DMW-LPL46) or ND filters (optional: DMW-LND46), or if using thick protectors and/or filters. ‰¥ The filter may become impossible to remove if excessively tightened, so please refrain from tightening it too strongly. ‰¥ It is possible to attach the lens cap with the filter already attached. Cautions for Use Take care not to drop or knock the lens. Also take care not to put a lot of pressure on the lens. ‰¥ Take care not to drop the bag that you inserted the lens in as it may strongly shock the lens. The camera may stop operating normally and pictures may no longer be recorded. [. . . ] ‰¥ Wipe off any dust or fingerprints with a soft, dry cloth. ‰¥ Use a dry dust cloth to remove dirt and dust on the focus ring. ≥ Do not use a household detergent or a chemically treated cloth. Troubleshooting A sound is heard when the camera is turned on or off. [. . . ]