User manual PANASONIC HH-S35100E

[. . . ] ‰¥ Four ThirdsTM and Four Thirds Logo marks are trademarks or registered trademarks of Olympus Imaging Corporation, in Japan, the United States, the European Union and other countries. ≥ G MICRO SYSTEM is an interchangeable lens type digital camera system of LUMIX based on a Micro Four Thirds System standard. ‰¥ Other names of systems and products mentioned in these instructions are usually the registered trademarks or trademarks of the manufacturers who developed the system or product concerned. Book 3 ページ ２０１２年９月１１日　火曜日　午後７時３５分 ENGLISH -If you see this symbol- Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. [. . . ] 1 2 3 4 VFC4430 VYC1085 VYF3480 VFC4605 1 2 3 4 Lens Storage Bag Lens Hood Lens Cap Lens Rear Cap (The lens rear cap and lens cap are attached to the interchangeable lens at the time of purchase. Book 6 ページ ２０１２年９月１１日　火曜日　午後７時３５分 Attaching/Detaching the Lens ≥ Refer also to the camera’s operating instructions for attaching and detaching the lens. ˆ« Detaching the Lens ≥ Check that the camera is turned off. ˆ«Attaching the Lens ≥ Check that the camera is turned off. A: Lens Rear Cap While pressing on the lens release button D, rotate the lens toward the arrow until it stops and then remove. €¢ Attach the lens rear cap so that the lens contact point does not get scratched. €¢ Attach the body cap to the camera so no dirt or dust will get inside the main unit. 2 Align the lens fitting marks B (red marks) on the camera body and the lens and then rotate the lens in the direction of the arrow until it clicks. ˆ« Attaching and Detaching the Lens Cap Pinch the lens cap as shown in the figure to attach or detach. €¢ Be careful not to lose the lens cap. €¢ Do not press the lens release button C when you attach a lens. €¢ Do not try to attach the lens when holding it at an angle to the camera body as the lens mount may get scratched. Book 7 ページ ２０１２年９月１１日　火曜日　午後７時３５分 ∫ Attaching the Lens Hood (Supplied Accessory) 2 Reverse the lens hood and then attach it in the same way as shown 1 Align the fitting mark E on the lens previously. Hood with the mark on the tip of the lens. €¢ When taking pictures with 2 Turn the lens hood in the direction of the flash with the lens hood the arrow until it stops, and align the attached, the lower portion of stop mark F on the lens hood with the screen may turn dark (vignetting effect) and the mark on the tip of the lens. The control of the flash may be disabled because the photo flash may be obscured by the lens hood. €¢ When using the AF assist lamp in the dark, detach the lens hood. ˆ« Attaching Filters ∫ Temporarily Storing the Lens Hood 1 Turn the lens hood in the direction of the arrow to detach it. ‰¥ Vignetting may occur if using 2 or more MC protectors (optional: DMW-LMCH58), PL filters (optional: DMW-LPL58) or ND filters (optional: DMW-LND58), or if using thick protectors and/or filters. ‰¥ The filter may become impossible to remove if excessively tightened, so please refrain from tightening it too strongly. ‰¥ It is possible to attach the lens cap with the filter already attached. ‰¥ You cannot attach a conversion lens or adaptor to this lens. [. . . ] ‰¥ Wipe off any dust or fingerprints with a soft, dry cloth. ‰¥ Wipe off the dust or dirt on the lens mount rubber (P8), zoom ring, or focus ring with a dry dust cloth. ≥ Do not use a household detergent or a chemically treated cloth. Troubleshooting A sound is heard when the camera is turned on or off. [. . . ]