User manual PANASONIC KV-S7075C

[. . . ] Operating Manual High Speed Color Scanner Model No. KV-S7075C These instructions contain information on operating the scanner. Before reading these instructions, please read the installation manual enclosed with this unit. Please carefully read these instructions and the enclosed installation manual. Keep all documentation in a safe place for future reference. Introduction Thank you for purchasing a Panasonic High Speed Color Scanner. About the documentation The scanner documentation consists of 2 manuals: the Installation Manual and the Operating Manual. [. . . ] When scanning important documents, confirm that the number of scanned images matches the number of pages in the document. Remove documents from the exit tray after they have been scanned. 15 Loading Documents on the ADF Scanning documents with pages of same sizes Cautions: Please remove any staples from the document before scanning. Glued or curled documents may cause a paper jam or damage the unit, so please scan using the flatbed. 1 Set the manual feed selector to [AUTO] or [MANUAL]. [AUTO]: Auto feeding [MANUAL]: Manual feeding When manually feeding a document, feed the document 1 page at a time. When scanning important documents or bound documents, feed them manually. [AUTO] Manual feed selector [MANUAL] Manual feed selector 2 Documents that have been stapled together or stacked together (as in a file folder) will need to be separated. 1 Fan the stack of documents to separate all the edges. 2 Hold both ends and bend the documents as shown in the illustration. 3 To flatten the documents, hold firmly and pull them apart as shown in the illustration. Repeat these steps as necessary. 1 2 3 3 16 Carefully align the documents. Loading Documents on the ADF 4 Adjust the document guides slightly larger than the actual size of the documents. Document guide 5 When using long paper, pull out the hopper extension tray from the hopper. Then raise and adjust the exit stopper to the position a little longer than the actual length of the document. Hopper Hopper extension tray Exit stopper 17 Loading Documents on the ADF 6 Place the documents on the hopper Portrait with the side to be scanned facing up. Then push them in the direction of the arrow until they stop. The amount of documents should not exceed the limit mark on the document guide. Fill indicator (Limit mark) Landscape 18 Loading Documents on the ADF 7 Adjust the document guide to the size of the document to be scanned. Adjust the exit stopper to the size of the document to be output. When scanning the document with the length between 420 mm (A3 size) or 432 mm (17 in. ) and 2540 mm (100 in. ) close the exit stopper. Document guide Exit stopper 8 Open your scanning application*1 and scan the documents. *1 The software RTIV and QuickScan Pro demo, included with the scanner, can be used for scanning the documents. 19 Loading Documents on the ADF Scanning documents with pages of different sizes For conditions when scanning documents with mixed page sizes, see "For documents with mixed page sizes and thicknesses" (page 15). When scanning different size documents, scanned sheets may need to be reordered for optimum performance. 1 Set the manual feed selector to [AUTO]. [AUTO] Manual feed selector 2 Documents that have been stapled together or stacked together (as in a file folder) will need to be separated. 1Fan the stack of documents to separate all the edges. 2 Hold both ends and bend the documents as shown in the illustration. 3 To flatten the documents, hold firmly and pull them apart as shown in the illustration. Repeat these steps as necessary. 1 2 3 3 Unlock the document guide. Slide the document guides selector in the direction shown in the illustration until the (1) and (2) marks are aligned to unlock the document guide. Document guides selector 1 2 20 Loading Documents on the ADF 4 Align the document pages along one side. 2 2 2 2 5 When using long paper, pull out the hopper extension tray from the hopper. Then raise and adjust the exit stopper to the position a little longer than the actual length of the document. Hopper Hopper extension tray Exit stopper 6 Align the document position so that the center of the smallest sheet will be fed to the center of the paper slot. If the document is not properly aligned, the pages will not be fed correctly. The amount of documents should not exceed the limit mark on the document guide. Depending on the types of paper, the document may not be fed smoothly. [. . . ] It can be carried out by means of the User Utility using the special shading paper, which is provided with this scanner. ¥When shading adjustment is required Proceed with the compensation when the colors in some parts of the scanned images differ in the extreme, or when the image quality fails to be improved even after the inside the scanner is cleaned. ¥Before proceeding with the shading adjustment Before proceeding, be absolutely sure to thoroughly clean the ADF glass (F) area, ADF glass (B) area, reference plate (F) and reference plate (B) as well as the transport path and drive rollers of the scanning unit. If the shading adjustment is carried out while these parts are still dirty, it will not be possible to eliminate the lines that form on the scanned images. ¥Shading adjustment procedure 1. Click "User Shading" on the main menu, and operate as the image display dictates. For further details, refer to section 4. 6 in the User Utility Reference Manual. ¥Caution If the scanned images are still lined after the shading adjustment has been performed and if these lines are not eliminated even after the ADF glass areas have been cleaned, it means that the shading has not been compensated properly. [. . . ]