User manual PANASONIC KV-S2025CU

[. . . ] KV-S2025C / KV-S2025CU / KV-S2026C / KV-S2026CU KV-S2045C / KV-S2045CU / KV-S2046C / KV-S2046CU KV-S2025C KV-S2025CU KV-S2026C KV-S2026CU KV-S2045C KV-S2045CU KV-S2046C KV-S2046CU These instructions contain information on operating the scanner. Before reading these instructions, please read the installation manual enclosed with this unit. Please carefully read these instructions, the enclosed installation manual and maintenance manual. Keep all documentation in a safe place for future reference. [. . . ] (The LED will now light. ) Turn on the power of the host computer after scanner's LED lights green. In case of the USB connection, the host computer recognizes the scanner automatically when the scanner is powered on even after the host computer is powered on. LED About LED LED indicates the status of the scanner as follows: LED light Green Green (flashing) Orange Orange (flashing) Red Status Ready to scan or scanning Sleep mode Ready to scan or scanning with warning *1 Initializing Sleeping with warning *1 An error occurred *2 *1: The rollers need to be cleaned or replaced. *1*2: Check the status of the scanner using the User utility. The User utility is included in the CD-ROM. 15 Component Identification About the SCSI setting When connecting the scanner to a SCSI chain using a SCSI cable, perform the SCSI ID setting correctly. The scanner is provided with a DIP switch for the SCSI ID No. setting and the terminator setting. SCSI ID Setting Switch ID No. #2 0 1 2 3 4 5 6 7 OFF OFF OFF OFF ON ON ON ON OFF OFF ON ON OFF OFF ON ON #1 OFF ON OFF ON OFF ON OFF ON Default setting #0 Remarks SCSI Terminator Setting Function Enable Disable ON OFF Switch Description The last device in the SCSI chain Default setting Not the last device in the SCSI chain 16 Loading Documents 1 Documents that have been stapled together or stacked together (as in a file folder) will need to be separated. 1 Fan the stack of documents to separate all the edges. 2 Hold both ends and bend the documents as shown in the illustration. 3 To flatten the documents, hold firmly and pull them apart as shown in the illustration. Repeat these steps as necessary. Prior to scanning, remove, all staples and paper clips from pages. 1 2 3 2 3 Carefully align the documents. Adjust the document guides slightly larger than the actual size of the documents. Document guides 17 Loading Documents 4 When scanning paper longer than the Feed extension tray feed tray, pull out the feed extension tray from the feed tray and the exit extension tray as shown in the figure on the right. The exit extension tray of KV-S2045C, KV-S2045CU, KV-S2046C and KV-S2046CU is fixed. Adjust the position of the exit stopper. Exit stopper Exit extension tray When using small sized documents like business cards, raise the business card guides and the business card stopper. Caution: Do not use the business card guides and the business card stopper for larger documents than their acceptable size. It will cause paper jams. A Business card guides Business card stopper 5 Place the documents on the feed tray with the side to be scanned facing up. Be sure to place the documents on the feed tray as shown in the figure on the right. The amount of documents should not exceed the limit mark on the document guide. Paper feed roller Feed tray 18 Loading Documents 6 Adjust the document guides to the size of the documents. Document guides 7 Set documents under the paper feed roller. 1 Lift the paper feed roller as shown in the figure. 2 Push documents in the direction of the arrow until they stop under the paper feed roller. Paper feed roller 1 2 Caution: Acceptable documents are as follows. Paper size: 50. 8 k 70 mm (2. 0 k 2. 8 in. ) to 216 k 356 mm (8. 5 k 14 in. ) Paper thickness: Single paper feed: 0. 05 to 0. 15 mm (2. 0 to 5. 9 mils) Continuous paper feed: 0. 06 to 0. 15 mm (2. 36 to 5. 9 mils) Paper weight: Single paper feed: 40 to 127 g/m2 (10. 7 to 33. 9 lbs. ) Continuous paper feed: 50 to 127 g/m2 (13. 3 to 33. 9 lbs. ) If you scan other types of documents, paper jamming or multiple-sheet feeding may occur. Scanning paper such as carbons or carbonless paper may cause skewing, paper jamming or multiple-sheet feeding because it makes the rollers dirty and the chemicals may cause the rollers to swell up. The amount of documents should not exceed the limit mark on the document guide. Be sure to remove the document from the exit tray after it is scanned. [. . . ] (See page 17. ) Flatten the document and load it again. (See page 23. ) Replace the paper feed roller module and the retard roller module. (See page 27 and page 30. ) Flatten the document and load it again after reducing the pages. Make a copy of the document on specified paper (see page 35) and scan the copy. [. . . ]