User manual PANASONIC KV-S2065W

[. . . ] Model No. KV-S2065L / KV-S2065W These instructions contain the information on operating the scanner. Before reading these instructions, please go through the installation manual enclosed with this unit. Please carefully read these instructions, the enclosed installation manual and maintenance manual. Keep these documentation in safe place for future reference. [. . . ] If "0" character is set, printing starts from 10. 0 mm. The millimeter value displayed is an approximation. · This setting can be done only when a pre-imprinter is installed. 02. Pre Posi t ion 1Cha r 1 2 . 4 mm The length per character varies, depending on the 04 orientation setting. 90°or 270°: 2. 40mm per character 0°or 180°: 3. 46mm per character Character: 0 - 72 · In this example, printing starts at 12. 4 mm (approx. The number 12. 4 can be changed from 10. 0 to 182. 8 by pressing the 1 key or the 2 key. Top of the paper 10mm (Default) Approx. 13/32 in. Top of the paper 12. 4mm Approx. 1/2 in. ABCD . . . . . . Top of the printout ABCD . . . . . . Top of the printout 03 Setting the pre-imprinter font style Host Bold Normal Font Hos t 03. Pre · This setting can be done only when a pre-imprinter is installed. Bold : Normal: 2-dot font 1-dot font that can increase the ink lifetime longer than Bold fonts. 25 Display Panel Instructions 04 Setting the pre-imprinter orientation 04. Pre Ro t a t e Hos t Host 0o 90o 180o 270o · This setting can be done only when a preimprinter is installed. 0x 90x 180x 270x :Transfer direction A Prints portrait orientation. B Rotates character string 90 degrees and prints. AB A B AB Prints portrait orientation from the end of the character string. Rotates character string 270 degrees and prints. 11 Setting the post-imprinter data 11 . Pos t Imp r i n t Hos t This is the same as the pre-imprinter. See "01 Setting the pre-imprinter data". · You cannot set the pre-imprinter and post-imprinter to "Count" at the same time. · This setting can be done only when a postimprinter is installed. 12 Setting the post-imprinter position 12 . Pos t Pos i t ion Hos t This is the same as the pre-imprinter. See "02 Setting the pre-imprinter position". · This setting can be done only when a postimprinter is installed. 13 Setting the post-imprinter font style 13 . Pos t Font Hos t This is the same as the pre-imprinter. See "03 Setting the pre-imprinter font style". · This setting can be done only when a postimprinter is installed. 14 Setting the post-imprinter orientation 14 . Pos t Ro t a t e Hos t This is the same as the pre-imprinter. See "04 Setting the pre-imprinter orientation". · This setting can be done only when a postimprinter is installed. 26 Display Panel Instructions Others setting menu (by pressing the OTHERS key) Number, mode and default display next mode. Contents · Pressing the 3 key will change to the · Pressing the 1 key or the 2 key will change to another value. · Pressing the 4 key will change to the previous mode. 01 Checking the version MX. XX : FX. XX : Displays the mechanical control firmware version. Displays the pre-imprinter firmware version. [. . . ] (See page 39. ) Open the front door and remove the jammed paper. (See page 35. ) Close the front door. The rollers need to be replaced. Multiple sheets were fed into the unit. VVVWa r n i n g VVV Db l . Feed Occu r ed U11 J AM !!!!!!!! The document is jammed. U12 J AM !!!!!!!! The document is jammed. U13 J AM !!!!!!!! The document is jammed. U14 J AM !!!!!!!! The document is jammed. U15 J AM !!!!!!!! The document is jammed. U16 J AM !!!!!!!! The document is jammed. U17 J AM !!!!!!!! The document is jammed. [. . . ]