User manual PANASONIC KV-S6050W

[. . . ] Model No. KV-S6050W / KV-S6055W / KV-S6050WU / KV-S6055WU These instructions contain the information on operating the scanner. Before reading these instructions, please go through the installation manual enclosed with this unit. Please carefully read these instructions, the enclosed installation manual and maintenance manual. Keep these documentation in a safe place for future reference. [. . . ] XX 02 Setting the "Buzzer" 02 . Buzzer ON ON OFF 03 Setting the SCSI ID ID No . SCS I 0 1 2 3 4 5 6 7 · Setting the SCSI ID will be activated after turning the power off and turning it on again. 04 Setting the "Terminator" Disable Enable 04. Terminator Enable When the scanner is located to terminal position on SCSI bus, set to "Enable". · Setting the terminator will be activated after turning the power off and turning it on again. · The internal terminator works only when the units power has been turned on. If the PC is to be used while the unit's power is off, be absolutely sure to install an external terminator which is available on the market. 05 Setting the transfer rate 20MByte/sec 10MByte/sec 05. Transfer Ra t e 2 0MB y t e / s e c · Changes the maximum value of the synchronous transfer rate of the SCSI interface. · Lower the synchronous transfer rate to 10 Mbytes/sec. if the computer has failed to recognize the scanner or the scanner fails to operate properly. 30 Display Panel Instructions 06 Checking the "Roller Cleaning Warning" Ro l ler 0% 0% 06. Clean Wa r n i n g : This is displayed when "Clean Roller Warning %" displayed is cleared. 100% : This is displayed when the roller needs to be cleaned. 06 Clearing the "Roller Cleaning Warning" 06. Clean Ro l l e r Wa r n i n g Clear=<> When pressing the 1 key and the 2 key simultaneously, "Clean Roller Warning" will be cleared. Then "Completed" will be displayed. 07 Checking the roller modules replacement warning Ro l l. 0% 07 . Rep l ace Wa r n i n g : This is displayed when "Replace Roll. 100% : This is displayed when the roller modules need to be replaced. When pressing the 1 key and the 2 key simultaneously, "Replace Roll. Then "Completed" will be displayed. 0% 07 Clearing the roller modules replacement warning 07 . Rep l ace Ro l l . Wa r n i n g Clear=<> 31 Display Panel Instructions 08 Setting the "Product ID" · KV-S6055W series KV-S6055 KV-S2065 KV-SS855 KV-S2055 KV-S6045 08. Product ID KV-S6055 · KV-S6050W series KV-S6050 KV-S2065 The applications for the scanner which have been set can be used. · An error results if an attempt is made to use a function which are not provided with the KV-S6050W or KV-S6055W series of scanners. · No guarantees are given for complete compatibility. Disable KV-SS855 KV-S2055 KV-S6040 09. Sleep Mode After 15mi n . To conserve energy and operating cost, this scanner is provided with a programmable power save feature. The scanner is factory set with the power save feature (sleep mode) turned on to comply with ENERGY STAR® requirement. If sleep mode is enabled, the scanner enters the sleep mode when the scanner is idle for 15 minutes. · 1min. · To return from the sleep mode, press any key on the scanner or issue the scan instruction from the application. 32 Display Panel Instructions ¥ Other display explanations Display Content This will be displayed when scanning is started until it is completed. After completion, "Ready" will be displayed. If the STOP key is pressed, scanning will stop. This will be displayed when the STOP key is pressed during scanning. [. . . ] J AM !!!!!!!! The document is jammed or the document has been feeded obliquely. Open the front or ADF door and remove the jammed paper. (See pages 42 and 43. ) A document remains in the scanner. U18 Rema i nd Doc . !!!!!!!! Open the front or ADF door and remove all of the remaining documents. (See pages 48 and 49. ) Open the ADF door and remove the paper. [. . . ]