User manual PANASONIC KX-TD1232E

[. . . ] Digital Super Hybrid System Please read this manual before connecting the Digital Super Hybrid System. DIGITAL SUPER HYBRID D1232 SYSTEM DIGITAL SUPER D816 HYBRID SYSTE M MODEL KX-TD816E / KX-TD1232E Panaso nic Panaso nic KX-TD816 KX-TD1232 Thank you for purchasing the Panasonic Model KX-TD816E/KX-TD1232E, Digital Super Hybrid System. System Components Model Service Unit Telephone KX-TD816E KX-TD1232E KX-T7420E KX-T7425E KX-T7431E KX-T7433E KX-T7436E KX-T7220E KX-T7230E KX-T7235E KX-T7250E KX-T7130E KX-T7020E KX-T7050E KX-T7440E KX-T7441E KX-T7240E KX-T7040E KX-TD170E KX-TD180E KX-TD181E*1 KX-TD182E*2 KX-TD190E KX-TD192E*1 KX-TD196E*1 KX-TD197E KX-TD198E*2 KX-TD199E*2 KX-TD280E KX-TD281E*1 KX-TD282E*2 KX-TD286E KX-TD290E KX-TD142 KX-TD144 KX-TD146 KX-T30865E KX-A46E Description Digital Super Hybrid System (Main Unit) Digital Super Hybrid System (Main Unit) Digital proprietary telephone Digital proprietary telephone Digital proprietary telephone with 1-line display Digital proprietary telephone with 3-line display Digital proprietary telephone with 6-line display Digital proprietary telephone Digital proprietary telephone with 2-line display Digital proprietary telephone with 6-line display Digital proprietary telephone Proprietary telephone with 1-line display Proprietary telephone Proprietary telephone Digital DSS Console Digital Attendant Console Digital DSS Console DSS Console 8-Station Line Unit 4-CO Line Unit 8-CO Line Card 4-CO Line Card Message Unit System Inter Connection Card (two cards with Connection Cable) Remote Card 9600bps Speed Remote Card 9600bps Speed Remote Unit Message Card 2-ISDN S0 Line Unit 4-ISDN S0 Line Card 2-ISDN S0 Line Card 6-ISDN S0 Line Unit Primary Rate Interface (PRI) ISDN Expansion Unit Cell Station Cell Station Interface Unit Doorphone Battery Adaptor Optional Equipment System Components Table Note In this Installation Manual, the suffix "E" of each model number is omitted. The Digital Super Hybrid System is abbreviated as "DSHS. " The Digital Proprietary Telephone is abbreviated as "DPT. " Other proprietary telephone (analogue type) is abbreviated as "APT. " A Single Line Telephone is abbreviated as "SLT. " 2 *1: Available for KX-TD1232 only. *2: Available for KX-TD816 only. Important Information FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. [. . . ] Press END. Conditions · The valid characters are 0 through 9. · To assign all CO lines to one selection, press the key at step 3. In this case, the display shows the contents programmed for CO01. · In case of the KX-TD1232, CO 01 through CO 12 are for the Master System and CO 13 through CO 24 are for the Slave, If available. · CO09 through CO16 of KX-TD816 and CO025 through CO54 of KXTD 1232 become available when the expansion unit KX-TD290 is installed in the main unit. · To display parts of the number which have scrolled off the display, press or . Section 3, Features, Calling Line Identification Restriction (CLIR) Connected Line Identification Restriction (COLR) Feature References 4-104 System Programming 4. 6 Description CO Line Programming 420/429 ISDN Ring Service Assignment -- Day / Night Assign the contract status of the Direct Dialling In (DDI) Service or Multiple Subscriber Number on a CO line basis in both day and night modes. This setting is also used for Calling Line Identification Presentation (CLIP) and Connected line Identification Presentation (COLP). · CO line number: KX-TD816 ­ 01 through 08, ( =all CO lines) KX-TD1232 ­ 01 through 24, ( =all CO lines) · DDI / MSN / Disable All CO lines ­ DDI -- Day / Night 1. Enter a program address (420 for day or 429 for night). Display example: DDI Service Day Selection Default Programming Press NEXT. Display: CO Line NO? Enter a CO line number. To enter CO line number 01, you can also press NEXT. 8. Keep pressing SELECT until the desired selection is displayed. To program another CO line, press NEXT or PREV, or SELECT and the desired CO line number. Press END. Conditions · In case of the KX-TD1232, CO01 through CO12 are for the Master System and 13 through 24 are for the Slave, if available. · To assign all CO lines to one, press the key in step 3. In this case, the display shows the contents programmed for CO01. · If "DDI" is selected, the subscriber number and extension number is provided to ISDN for CLIP and COLP. Section 3, Features, Direct Dialling In (DDI) Feature References System Programming 4-105 421 Description 4. 6 CO Line Programming CO Line Name Assignment Assigns the company or customer names to each CO line so that the operator or extension user can find the destination where the caller is trying to reach before answering. · CO line number: KX-TD816 ­ 01 through 8, ( =all CO lines) KX-TD1232 ­ 01 through 24, ( =all CO lines) · Name: 10 characters (max. ) All CO lines ­ Not stored 1. Enter 421. Display: CO Line Name Selection Default Programming Press NEXT. Display: CO Line NO? Enter a CO line number. To enter CO line number 01, you can also press NEXT. Display example: CO01:Not Stored 4. Enter a name. For entering characters, see Section 4. 1. 3 "Entering Characters. " To delete the current entry, press CLEAR. To change the current entry, press CLEAR and the new name 5. To program another CO line, press NEXT or PREV, or SELECT and the desired CO line number. [. . . ] It is eight locations for entering CS ID numbers for Site Survey Enter a spare location number, The TD7500 can store 8 CS ID's for Site Surveying . The CS ID number is not related to the CS number on the PBX CS ID1 = CS ID1 = 0123456789 A ~ F are the 6 Function Keys below the Number Pad To Save If more than one Cell Station is to be surveyed repeat this step for the other CS ID's Returns to Main Menu To clear CS ID numbers ( can be overwritten ) To enter Survey Mode : Switch PS On while pressing, `TALK' + `FLASH ( )' + `*' . Step [3] [ TALK ] Display : Entry FUNCTION < 0 ­ 4 > CS ­ ID CLEAR, CS NO?( 1 ­ 8 ) Enter CS Number to be cleared. CS ID Cleared Repeat for other CS Numbers 4 Site Survey Assigning a PS ( TD7500 ) to a Cell Station To enter Survey Mode : Switch PS On while pressing, `TALK' + `FLASH ( )' + `*' . Step [0] [ TALK ] [ CLR ] [ TALK ] [0~9] [ TALK ] Display : Entry FUNCTION < 0 ­ 4 > Current Status Displayed To Survey other slots : Press [ # ] (Next) or [ * ] (Previous) To Survey other channels : Press [ 0 ~ 9 ] To record results ** All Book Data is cleared ** To return to test result display To Clear all Log data, Press ( . [. . . ]