User manual PANASONIC KX-TG4000

[. . . ] 2. 4GHz Multi-Handset Cordless Phone System Model No. KX-TG4000B Pulse-or-tone dialing capability Operating Instructions 4-LINE Caller ID Compatible PLEASE READ BEFORE USE AND SAVE. Charge the handset battery for about 8 hours before initial use. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Before Initial Use Please read IMPORTANT SAFETY INSTRUCTIONS on page 102 before use. Read and understand all instructions. Thank you for purchasing your new Panasonic cordless telephone. Caller ID and Call Waiting Service, where available, are telephone company services. After subscribing to Caller ID, this phone will display a caller's name and phone number. Call Waiting Caller ID, which displays a second caller's name and phone number while the user is on another call on the same line, requires a subscription to both Caller ID and Call Waiting. Attach your purchase receipt here. For your future reference Serial No. (found on the bottom of the unit) Date of purchase Name and address of dealer 2 Accessories (included) For extra orders, call 1-800-332-5368. AC Adaptor for Base Unit (p. [. . . ] Make sure that the base unit and cordless handset are in the standby mode. Base unit Cordless handset 1 2 3 Press (FUNCTION). Press or until the arrow points to "Registration", and press H. Press or until the arrow points to "Deregistration", and press H. · The registered handset numbers are displayed. 1 2 3 Press (FUNCTION). Press or until the arrow points to "Registration", and press H. Press or until the arrow points to "Deregistration", and press H. Deregister?Handset3 CLEAR=Yes I=No · To stop, press I. Deregistering HS No. :12345678 ENTER=Set IH 4 5 Press H or I to move the cursor to the handset number to be canceled. Handset3 CLEAR=Yes I= N o · To stop, press I. 4 Press (CLEAR). · A beep sounds and "Clear" is displayed. · To return to the standby mode, press (EXIT). · [­] will be displayed. 6 Press (CLEAR). · A beep sounds and "Clear" is displayed. · To cancel registration of another handset, start again from step 3. · To return to the standby mode, press (EXIT). The canceling procedure must be carried out with both the base unit and the cordless handset. · The cordless handset will not work. To use it again, registration will be required (p. 19, 53). 54 Selecting the Line Mode Base Unit If the line is connected to a low voltage system such as a PBX, set to "B". Otherwise, the line indicator may not operate properly, the Call Waiting Caller ID feature may not be used (p. 46), you may not hear the incoming call tone (p. 51), and the unit may not alert your pager (p. Make sure that the base unit is in the standby mode. 1 2 3 Press (FUNCTION). Press or until the arrow points to "Line setting", and press H. Press or until the arrow points to "Set line mode", and press H. · The current settings are displayed. 4 5 Select "B" or "A" by pressing or for each line. · To return to the standby mode, press (EXIT). Chapter 3 Line mode L1 L2 L3 A A A L4 A Erasing the Directory, Caller List and Redial List Base Unit Handset You can erase all entries in the directory, caller list and redial list. Programming must be carried out separately for the base unit and cordless handset(s). Make sure that the base unit/cordless handset is in the standby mode. Advanced Operation 1 2 3 Press (FUNCTION). [. . . ] To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the cordless telephone further away from the TV or VCR. This will often reduce or eliminate interference. Operating near 2. 4GHz electrical appliances may cause interference. [. . . ]