User manual PANASONIC KX-TG5230

[. . . ] 5. 8 GHz Expandable Cordless Phone System Operating Instructions Model No. KX-TG5230 Pulse-or-tone dialing capability The unit is Caller ID compatible. To display the caller's name and phone number, you must subscribe to Caller ID service. PLEASE READ BEFORE USE AND SAVE. Charge the battery for 6 hours before initial use. Panasonic World Wide Web address: http://www. panasonic. com for customers in the USA or Puerto Rico Thank you for purchasing your new Panasonic cordless telephone. Please read the IMPORTANT SAFETY INSTRUCTIONS on page 73 before use. [. . . ] 3). Advanced Operation Base Unit When the base unit is being paged, it rings and the LOCATOR/INTERCOM/ TRANSFER indicator flashes. 1 Press [SP-PHONE] or [LOCATOR/INTERCOM/TRANSFER]. 2 To disconnect the intercom, press [SP-PHONE] or [LOCATOR/INTERCOM/TRANSFER]. Useful Information 43 · When the ringer volume is turned off (p. 18, 19), the handset and the base unit will ring at the low level for intercom calls. · You cannot change the ringer tone for intercom calls. · When the base unit user pages all handsets, only the handset user who answers first can talk with the base unit user. For assistance, please call: 1-800-211-PANA(7262) Intercom Voice Paging Base Unit The base unit user can make a voice announcement that is heard through the speakers of all handsets. · When 4 handsets are registered to the base unit, and if one handset user is on conversation using the Booster feature, 1 of the remaining 3 handsets will not receive the voice announcement. 1 Press [LOCATOR/INTERCOM/TRANSFER]. · The LOCATOR/INTERCOM/TRANSFER and SP-PHONE indicators light. 2 To make a voice announcement to all handsets, press [5] ( ). · You will hear a ringback tone (two short beeps) and the SP-PHONE indicator flashes. 3 When the SP-PHONE indicator stops flashing, speak into the MIC. · All handset users will hear your voice through their speakers after beeps, "Call from Base" will be displayed and the Ringer/Message Alert indicator will flash rapidly on the handsets. · The handset on the base unit will not be paged. 4 When finished, press [SP-PHONE] or [LOCATOR/INTERCOM/ TRANSFER]. OR After one of the handsets answers, talk into the MIC. To disconnect the intercom, press [SP-PHONE] or [LOCATOR/INTERCOM/TRANSFER]. · Only the handset user who answers first can talk with the base unit user. · To answer the page from the handsets, see "Answering Intercom Calls" on page 43. · If a handset is too close to the base unit, you may hear feedback while making the voice announcement. Place the handset on the base unit (or the charger, for accessory handset users, p. · It is not possible to specify which handset(s) will hear the voice announcement. · The announcement is heard at the handset ringer volume (p. 18). 44 Transferring a Call You can transfer an outside call to the base unit or a handset. From the Handset to the Base Unit Preparation 1 Handset: (1) During a call, press [HOLD/INTERCOM]. · The call is put on hold. Press extension# to transfer 1-4=Handset 0=Base (2) To page the base unit, press [0]. (3) Wait for the paged party to answer, then you can announce the transfer. · If the paged party does not answer, press [C] or [s] to return to the outside call. Telephone System 2 Base unit: Press [SP-PHONE] or [LOCATOR/INTERCOM/ TRANSFER] to answer the page. 3 Handset: To complete the transfer, press [OFF]. From the Base Unit to the Handset 1 Base unit: (1) During a call, press [LOCATOR/INTERCOM/TRANSFER]. · The call is put on hold. Advanced Operation (2) To page a specified handset, press its extension number [1] ( ) to [4] ( ). Wait for the handset user to answer, then you can announce the transfer. OR To make a voice announcement to all handsets, press [5] ( ), then speak into the MIC when the SP-PHONE indicator stops flashing. · If the paged party does not answer, press [LOCATOR/INTERCOM/ TRANSFER] to return to the outside call. Useful Information 2 Handset: Press [C], [s], or [HOLD/INTERCOM] to answer the page. · You can also answer a page by pressing any button except [d], [B] or [OFF]. 3 Base unit: To complete the transfer, press [SP-PHONE]. · When the base unit user calls all handsets, only the handset user who answers first can take the transferred call. For assistance, please call: 1-800-211-PANA(7262) 45 Transferring a Call From a Handset to another Handset (when the system has two or more handsets) 1 During a call, press [HOLD/INTERCOM], then page another handset by pressing its extension number ([1] to [4]). 2 Wait for the paged party to answer, then you can announce the transfer. · The paged handset user can answer by pressing [C], [s], or [HOLD/ INTERCOM]. [. . . ] (The unit operates in the frequency range of 5760MHz to 5840MHz, and the power output level can range 0. 25 to 0. 5 watts. ) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy. · Routine care -- wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive powder. [. . . ]