User manual PANASONIC KX-F2700EW

[. . . ] L Do not rub or use an eraser on the printed side of recording paper, as the print may smear. Declaration of Conformity: L Panasonic Communications Co. , Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: http://www. doc. panasonic. de Contact: Panasonic Services Europe a Division of Panasonic Marketing Europe GmbH Panasonic Testing Centre Winsbergring 15, 22525 Hamburg, Germany Note: L The suffix in the model number will be omitted in these instructions. [. . . ] 4. 10. 2 Storing undesired callers You can register up to 10 undesired numbers from the Caller ID list (page 17) if you do not wish to receive faxes from them. 1 Press {MENU} repeatedly to display "JUNK FAX PROH. ". 2 Press {>} repeatedly to display "JUNK LIST SET". i {SET} 3 Press {A} or {B} repeatedly to display the item you wish to prevent the fax reception from. i {SET} 4 Press {STOP} to exit the program. To display the junk fax prohibitor list 1. Press {MENU} repeatedly to display "JUNK FAX PROH. ". Press {>} repeatedly to display "JUNK LIST DISP. ". To print the junk fax prohibitor list 1. Press {MENU} repeatedly to display "JUNK FAX PROH. ". Press {>} repeatedly to display "JUNK LIST PRINT". To erase an item from the junk fax prohibitor list 1. Press {MENU} repeatedly to display "JUNK FAX PROH. ". 28 5. Copy Copying 5 Copy 5. 1 Making a copy 1 L If the document exceeds the memory capacity, copying of the exceeded document will be cancelled and this feature will be turned OFF automatically. To stop copying Press {STOP}. 5. 1. 1 More copying features To enlarge a document 1. The maximum recording time of your greeting message is either 16 seconds (default) or 60 seconds. We recommend you record a message of less than 12 seconds to make it easier to receive faxes. Make sure feature #77 is set to "TAM/FAX" (page 40) beforehand. record your greeting message to inform the caller that the unit will not record any incoming messages. To check the greeting message Press {GREETING CHECK}. L The unit will play the greeting message. 6. 1. 1 Erasing your recorded greeting message 1 {GREETING CHECK} L To cancel erasing, press {STOP}. 2 {ERASE} Note: L If you erase your TAM/FAX greeting message, the pre-recorded greeting message will be played when a call is received. {MIC} {ERASE} {SET} {GREETING CHECK} {GREETING REC} {STOP} 1 {GREETING REC} i {SET} L A long beep will sound. 2 Speak clearly about 20 cm away from {MIC}. 3 When finished recording, press {STOP}. Note: L You can change the maximum TAM/FAX greeting message recording time to 60 seconds (feature #54 on page 39). ­ If you change the setting to 60 seconds, we recommend that you tell the caller in your TAM/FAX greeting message to press *9 before starting the fax transmission. ­ If you change the setting from 60 seconds to 16 seconds, your current greeting message will be deleted. The pre-recorded greeting message will be played when a call is received. L If you change the maximum recording time of incoming messages to "GREETING ONLY" (feature #10 on page 35), the unit will answer a call with your current greeting message, and then hang up. Answering Machine (KX-FP218 only) Incoming Messages 6. 2 Listening to recorded messages When the unit has recorded new voice messages: ­ The {AUTO ANSWER} indicator will flash when auto answer is turned ON. [. . . ] 135 W (When copying a 100 % black document) Power supply: 220­240 V AC, 50/60 Hz Fax memory capacity*3: Transmission: Approx. 1 Test Chart in standard resolution, without using the Error Correction Mode. ) {PRINT REPORT} {SET} {MENU} {<}{>} {STOP} 1 {PRINT REPORT} 2 Press {<} or {>} repeatedly to display the desired item. 3 {SET} L If you select to print out a list or a report, printing will start. L If you select "AUTO JOURNAL" or "AUTO CALL. LIST", press {0} or {1} to select the desired setting, then press {SET}. [. . . ]