User manual PANASONIC KX-F550

[. . . ] THIS HANDSET EARPIECE IS MAGNETIZED AND MAY RETAIN SMALL FERROUS OBJECTS. UNPLUG THIS UNIT FROM POWER OUTLET/THE ETHERNET CABLE IF IT EMITS SMOKE, AN ABNORMAL SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN AUTHORIZED SERVICENTER. [. . . ] Tone Announce. Wait for an answer. Tone To allow/deny a paged announcement 7 7 2 2 1 1 1 0 Deny Allow C. Tone Message Waiting Caller Called extension To leave a message waiting indication When the called extension is busy or does not answer MESSAGE C. Tone To call back MESSAGE Log-in/Log-out 7 7 3 3 6 6 1 For Log-in 0 For Log-out ICD Group Specified extension no. All C. Tone Before Leaving Your Desk To set 7 5 0 message no. (1-9) parameter (if required) # Setting Absent Message To cancel 7 5 0 0 Both Calls Outside Calls Intercom Calls 0 7 1 1 2 Call Forwarding 2 3 4 5 0 All calls Busy No answer Busy/ No answer Cancel extension no. OR # outside phone no. C. Tone CO line access no. --4-- Features List Feature Operation Before Leaving Your Desk To lock 7 7 1 C. Tone Extension Dial Lock To unlock 7 7 0 extension PIN (max. Tone Setting the Telephone According to Your Needs 0 Both Calls Outside Calls Intercom Calls Do Not Disturb 7 1 1 2 1 0 Set Cancel C. Tone Extension Feature Clear To set 7 9 0 C. Tone 7 6 0 1 hour/minute (4 digits) 0 AM Timed Reminder 1 PM 0 1 To cancel once daily C. KX-A237 CAUTION: · The AC adaptor is used as the main disconnect device. Ensure that the AC outlet is located near the unit and is easily accessible. Note: · Consult your dealer for more details about the AC adaptor. · For extra orders for the accessories, call toll-free: 1-800-332-5368. -- 10 -- Wall Mounting 1 Pull down the handset hook until it locks, so the tab holds the handset. 2 Remove the attached stand. 2 1 3 Mount the unit on the wall. To temporarily place the handset down during a conversation, hook it over the top edge of the phone as shown. 83 mm (3-1/4 in) -- 11 -- Wall Mounting If you are using the Ethernet cable with boots, you can mount the unit on a wall using the wall mounting plate (included) by following the steps below. To AC Outlet Ethernet cable (Straight CAT 5 or higher cable) [not included] To a Switching Hub (LAN) 100 mm (3-15/16 in) 83 mm (3-1/4 in) for base unit 1 Install 2 screws spaced 83 mm (3-1/4 in) or 100 mm (3-15/16 in) apart, to the wall. 2 Insert the upper and lower tabs of the wall mounting plate (included) into the designated openings in the base unit, then slide it in the direction of the arrow until it clicks. 3 Mount the base unit securely on the wall. 83 mm 100 mm (3-1/4 in) (3-15/16 in) Screw -- 12 -- Important Safety Instructions When using this unit, basic safety precautions, including those below, should always be followed to reduce the risk of fire, electric shock and injury to persons. Follow all warnings and instructions marked on this unit. Unplug this unit from the AC outlet before cleaning. Do not use the unit near water, for example, near a bathtub, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. Serious damage and/or injury may result if the unit falls. The unit should never be placed near or over a radiator or other heat source. This unit should be operated only from the type of power source indicated on the unit label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Do not allow anything to rest on the power cord. [. . . ] It also should not be placed in rooms where the temperature is less than 5 °C (41 °F) or greater than 40 °C (104 °F). Allow 10 cm (3-15/16 in) clearance around the unit for proper ventilation. Placement 1) Do not place heavy objects on top of this unit. 2) Care should be taken so that objects do not fall onto, and liquids are not spilled into, the unit. Do not subject this unit to excessive smoke, dust, moisture, mechanical vibration, shock or direct sunlight. [. . . ]