User manual PANASONIC KX-FLB803EX

[. . . ] Operating Instructions Flat-Bed Multi-Function Laser Fax with Separator This pictured model is KX-FLB813. Model No. KX-FLB813EX KX-FLB803EX Flat-Bed Multi-Function Laser Fax Model No. Please read these operating instructions before using the unit and save for future reference. These units are compatible with Caller ID. To use this feature, you must subscribe to the appropriate service of your service provider. These models are designed to be used in Czech, Hungary and Slovakia. To use in Hungary and Slovakia, change the location setting (feature #114 on page 62). [. . . ] To make an enlarged copy of the bottom of the document, turn the document around, and then make a copy. L When using the scanner glass, the unit will only enlarge the right top corner of the document starting from the l mark on the unit. Example: 150% enlarged copy Using the auto document feeder: Original document Enlarged copy Using the scanner glass (1): Original document Reduced copy 1 6. 3. 3 To collate multiple copies (Auto document feeder only) The unit can collate multiple copies in the same order as the original document pages. Using the scanner glass (1): Original document Enlarged copy 1 1 2 3 4 5 6 Set the original. Press {V} or {^} repeatedly to display "ON". Copy Example: Making 2 copies of a 4-page original document 4 3 2 1 3 4 3 2 1 1 1 2 2 3 4 4 Collated pages Uncollated pages Note: L The unit will store the documents into memory while collating the copies. The maximum number of original document for collating copies depends on the contents of pages, resolution and contrast. Approximately 50 pages of ITU-T No. 1 Test Chart in "TEXT" mode can be stored at a time, if the unit has no documents in memory. See page 93 of the specifications in detail. L If memory becomes full while storing, the unit will only print out the stored pages. L The collating feature is effective only for this time. After copying, this feature will turn OFF automatically. 50 7. Multi-Function Station software Setup 7 Multi-Function Station software 1 Remove the USB interface cover (1). 7. 1 Connecting to a computer Panasonic Multi-Function Station software enables the unit to carry out the following functions: ­ Printing on plain paper, transparencies, labels and envelopes ­ Scanning documents and converting an image into text with Readiris OCR software ­ Scanning from other applications for Microsoft® Windows® that support TWAIN scanning ­ Storing, editing or erasing items in directories using your computer ­ Programming the features using your computer ­ Sending, receiving fax documents using your computer To use Multi-Function Station on your computer, the following are required: Operating System: Works with Windows 98/Me/2000/XP*1 CPU: Windows 98: Pentium® 90 MHz or faster Windows Me: Pentium 150 MHz or faster Windows 2000: Pentium 166 MHz or faster Windows XP*1: Pentium 300 MHz or faster RAM: Windows 98: 24 MB (32 MB or more recommended) Windows Me: 32 MB (64 MB or more recommended) Windows 2000: 64 MB or more Windows XP*1: 128 MB or more Other Hardware: CD-ROM drive Hard disk drive with at least 100 MB of available space USB interface *1 Multi-Function Station software does not work with Windows XP Professional x64 Edition (64bit), a new version of Windows XP Professional that was released in and after April, 2005. Important notice for the connection L Do not connect the USB cable before installing Multi-Function Station. Be sure to connect the USB cable in step 6 on page 52. 1 2 Connect the USB cable (1) to the USB port. 1 3 Attach the USB interface cover (1). 1 Note: L Be sure to use a Hi-Speed USB 2. 0 certified cable if your computer is equipped with the Hi-Speed USB 2. 0 interface. Please purchase a shielded Type-A male/Type-B male USB cable maximum length 2 metres. Warning: L To assure continued emission limit compliance, use only shielded USB cable (2 m or less in length). 7. 2 Installing MultiFunction Station L The screenshots shown in these instructions are for Windows XP and are included for reference only. 51 7. Multi-Function Station software L The screenshots shown in these instructions may differ slightly from those of the actual product. L Software features and appearance are subject to change without notice. 5 When the [Connect Type] dialogue box appears, select [Connect directly with a USB cable. ], then click [Next]. L The [Connect Device] dialogue box will appear. Connect the unit with the USB cable (page 51), then click [Next]. L If the unit is connected to your computer, the model name will be automatically detected. [. . . ] ­ Moist paper ­ Inkjet paper L Some paper only accepts print on one side. Try using the other side of the paper if you are not happy with the print quality or if misfeeding occurs. L For proper paper feeding and best print quality, we recommend using long-grained paper. L Do not use paper of different types or thickness at the same time. [. . . ]