User manual PANASONIC KXFLB851G

[. . . ] You may need them when maintaining or moving this unit. ) Model number suffix “EB” denotes UK model. EB GN GS RQT9743-B until 2013/03/01 SC-HC38_DBEB_DBGN_GS~RQT9743-B. book 2 ページ ２０１３年１月２１日　月曜日　午後１時６分 Caution for AC Mains Lead (For the AC mains plug of three pins) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse. [. . . ] Preparation Note down a frequency block that can be received in your region (e. g. , 12B 225. 648 MHz). 1 2 Press [PLAY MENU] repeatedly to select “SCANMODE”. 1 2 3 10 RQT9743 While “SCAN FAILED” is displayed. Press [PLAY MENU] repeatedly to select “MANUAL SCAN”. Press [3, 4] to select the frequency block that is receivable in your region and then press [OK]. Press [3, 4] to select “ALL BAND III” or “LOCAL” and then press [OK]. ≥ The “DAB AUTO SCAN” begins automatically. ≥ The DAB preset channels are erased when the “SCANMODE” is changed. ≥ If the play timer has been set and DAB/DAB+ is the music source, the timer switches off. (l 12) SC-HC38_DBEB_DBGN_GS~RQT9743-B. book 11 ページ ２０１３年１月２１日　月曜日　午後１時６分 Listening to FM/AM radio AM radio is only available for [SC-HC38] ([Australia[and[New[Zealand[ only). You can preset up to 30 FM channels / 15 AM channels. Preparation ≥ Make sure that the antenna(s) are connected. ≥ Press [RADIO] to select “FM” or “AM”. ∫ Manual tuning and presetting Select a radio broadcast. 1 2 3 Press [PLAY MENU] repeatedly to select “TUNEMODE”. Press [3, 4] to select “MANUAL” and then press [OK]. Press [:/6] or [5/9] to tune to the required station. ≥ To start automatic tuning, press and hold [:/6], [5/9] until the frequency starts scrolling. ≥ To turn the timer off, select “OFF”. *1: This function can also be selected with the [D. BASS] button on the unit. ≥ You may experience a reduction in sound quality when these effects are used with some sources. If this occurs, turn the sound effects off. Press [Í] to turn the unit off. Clock and Timer Setting the clock This is a 24-hour clock. 1 2 Press [SETUP] repeatedly to select “CLOCK”. Press [3, 4] to set the time and then press [OK]. ≥ To display the clock, press [SETUP] to select “CLOCK” and then press [OK] once. (During standby, press [DISPLAY] once. ) ≥ The clock is reset when there is a power failure or when the AC mains lead is removed. ≥ Reset the clock regularly to maintain accuracy. ≥ To display the timer settings, press [SETUP] repeatedly to select “TIMER ADJ” and then press [OK] once. The music source and volume will also be displayed if the timer is turned on. ≥ During standby, if the timer is turned on, press [DISPLAY] twice to display the settings. ≥ This unit can be used as normal after the timer is set, however: – Turn the unit to standby mode before the timer start time. – Even if the audio source or the volume is changed, the timer will still use the audio source and volume that was set when the timer was turned on. *1: “CD”, “USB”, “IPOD_PORT”, “IPOD_DOCK”, “DAB/DAB+” ([SC-HC38DB]), “FM” and “AM” ([SC-HC38] ([Australia[and[New[Zealand[ only)) can be set as the music source. Sleep timer The sleep timer can turn the unit off after a set time. 1 2 Press [SETUP] to select “SLEEP”. [. . . ] Please note that freight and insurance to and / or from your nearest Authorised Service Centre must be arranged by you. Note that home or pick-up/delivery service is available for the following products in the major metropolitan areas of Australia or the normal operating areas of the nearest Authorised Service Centres: Plasma/LCD televisions / displays (screen size greater than 103 cm) 7. The warranties hereby conferred do not extend to, and exclude, any costs associated with the installation, de-installation or re-installation of a product, including costs related to the mounting, de-mounting or remounting of any screen, (and any other ancillary activities), delivery, handling, freighting, transportation or insurance of the product or any part thereof or replacement of and do not extend to, and exclude, any damage or loss occurring by reason of, during, associated with, or related to such installation, de-installation, re-installation or transit. Panasonic Authorised Service Centres are located in major metropolitan areas and most regional centres of Australia, however, coverage will vary dependant on product. [. . . ]