User manual PANASONIC KX-HCM110A

[. . . ] Operating Instructions Network Camera Model No. KX-HCM110A Please read this manual before using and save this manual for future reference. Panasonic Network Camera Website: http://www. panasonic. com/netcam for customers in the USA or Puerto Rico Operating Instructions Main Features IPv6*1 Network Camera Your Panasonic Network Camera supports IPv6 (Internet Protocol Version 6), IPv6 was created to address the additional IP addresses that will be needed as the Internet continues to expand. Since the camera also supports IPv4 that's currently used, it is "dual stack" design will seamlessly operate while IPv6 is phased in. For more information in IPv6 you wish to visit http://www. ipv6. org/. [. . . ] Click [Go to Date and Time page]. [For assistance, please call: 1-800-272-7033] 71 Operating Instructions Note Date and time settings become incorrect depending on the length of power-on time or the internal temperature. Using the Automatic Time Adjustment is recommended. 72 Operating Instructions 2. 10 Changing Camera Settings The Camera page allows you to set the camera name, white balance, AC power source frequency, pan/tilt range, return to specified position and color night view settings. 1. Set each parameter. · Clicking [Cancel] cancels your settings without saving changes. [For assistance, please call: 1-800-272-7033] 73 Operating Instructions Setting Camera Name · · Description The camera name is displayed on the Single Camera page. Enter ASCII characters (see page 168) or characters in each language (1--15 characters for a 1-byte character and 1--7 characters for a 2-byte character). But [Space], ["], ['], [&], [<], and [>] are not available. White Balance Select from the following options. · · · · · · Auto (default) Fixed Indoor Fixed Fluorescent (White) Fixed Fluorescent (Daylight) Fixed Outdoor Hold -- Automatic adjustment -- Electric bulb (2800 K) -- White (3600 K) -- Daylight (4000 K) -- Solar light (6000 K) -- Setting [Hold] keeps the current white balance. Note White balance is also saved in the home position, alarm position and preset buttons. AC Power Source Frequency It can select Flicker Correction by power line frequency. ­ 60 Hz (default) ­ 50 Hz Select 60 Hz in the United States. · 74 Operating Instructions Setting Pan Range*1 Description Select from the following options. · · · · Minimum Home Position*2 Maximum -- Current settings, -60--+60 -- Current settings, -60--+60 -- Current settings, -60--+60 The values must be selected as minimum home position maximum. Note If you wrongly set the range, your privacy may be seen. Tilt Range*1 Select from the following options. · · · · Minimum Home Position*2 Maximum -- Current settings, -45--+20 -- Current settings, -45--+20 -- Current settings, -45--+20 The values must be selected as minimum home position maximum. Note If you wrongly set the range, your privacy may be seen. Return to Specified Position · · If the camera is not operated during the specified period, the camera turns to the specified position. ­ Time - Do not move, 10 min, 30 min, 1 h ­ Specified Position - Home Position, Preset No. 1--8, Alarm No. 1, Alarm No. 2 Note If you did not set any presets, the camera cannot turn to the preset position. [For assistance, please call: 1-800-272-7033] 75 Operating Instructions Setting Color Night View · Description In the color night view mode, the camera image becomes brighter in a low illuminance. The camera image returns normal operation in a bright location. If you enable the color night view mode, refresh interval may slow down. · Note In the color night view mode, the image may have white or colored circles around the object. This is not a problem, since it is a CMOS sensor characteristic. *1 *2 See page 77 for details about pan/tilt range settings. These home position settings are displayed as you set on page 26. 3. Click [Save] when finished. · · · New settings are saved. If the [Pan Range] or [Tilt Range] settings are changed, the camera turns to the home position. When finished, "Success!" is displayed. Click [Go to Camera page]. 76 Operating Instructions Specifying Pan/Tilt Range 1. [. . . ] Proxy settings are not required. [For assistance, please call: 1-800-272-7033] 165 Operating Instructions 5. Enter the camera IP address into the Do not use proxy server for addresses beginning with data field. Click [OK]. Note When accessing the camera via a proxy server, the Talk Button is displayed gray. Talk feature cannot be used. 166 Operating Instructions 3. 9. 2 Setting UPnPTM to Display Camera Shortcut in My Network Places To display the camera shortcut in the My Network Places folder, Windows component should be added. [. . . ]