User manual PANASONIC KXHNS101E

[. . . ] Installation Guide Home Network System Window/Door Sensor Model No. KX-HNS101E Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 19). Please read this document before using the unit and save it for future reference. [. . . ] For more information about collection and recycling, please contact your local municipality. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. Helpline Tel. 0330 3331112 Ireland 01 4475228 7 HNS101E_(en_en)_0421_ver. 060. pdf 7 2015/04/21 14:21:40 Important Information Note for the battery symbol This symbol (B) might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Note for the battery removal procedure Refer to “Inserting the battery” on page 10. 8 Helpline Tel. 0330 3331112 Ireland 01 4475228 HNS101E_(en_en)_0421_ver. 060. pdf 8 2015/04/21 14:21:40 Setup Part names and functions n Sensor unit n Magnet unit LED indicator You can press M N and check the LED indicator to confirm the sensor’s status. Indicator Status Window/door is closed Window/door is open Sensor is out of range of the hub Registration mode (You pressed and held N) M No battery power Green, lit Red, lit Red, blinking A D E E Green, blinking Off B C Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 11). Setup overview 1 Initial setup Make sure you can access the system using your mobile device. For details, refer to the System Setup Guide included with your hub. Insert the battery The window/door sensor is battery powered. Registration Required only if the window/door sensor was purchased separately (i. e. , not as part of a bundle). Confirm the installation area Read the information in this document to confirm that the Sensor unit cover M N Used to confirm the status of the sensor or register the sensor to the hub. LED indicator Magnet unit cover “ ” marks Used to align the sensor and the magnet unit when installing them (page 13). 2 3 4 Helpline Tel. 0330 3331112 Ireland 01 4475228 11 HNS101E_(en_en)_0421_ver. 060. pdf 11 2015/04/21 14:21:40 Setup Wireless communication range The wireless communication range of each device in the system from the hub is approximately 50 m indoors and approximately 300 m outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other devices. R Metal doors or screens R Walls containing aluminium-sheet insulation R Walls made of concrete or corrugated iron R Double-pane glass windows R Multiple walls R When using each device on separate floors or in different buildings Note: R You can check the window/door sensor’s communication status by pressing M N. If the LED indicator is lit in green or red, the sensor is communicating properly with the hub. If the LED indicator blinks in red, it is out of range of the hub. 12 Helpline Tel. 0330 3331112 Ireland 01 4475228 HNS101E_(en_en)_0421_ver. 060. pdf 12 2015/04/21 14:21:40 Setup Temporary placement Before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing M N. Important: R Attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door. R The window/door sensor will not operate properly if the “ ” marks are too far apart or are not pointing toward each other. R Attach both units so that the “ ” marks point toward each other and are within 25. 4 mm of each other. Confirming proper operation After temporarily placing the window/door sensor in the desired location, press M N while the window or door is closed. The window/door sensor’s LED indicator lights as follows. [. . . ] The battery life differs depending on the capacity of the battery used. R Dimensions (height ´ width ´ depth) Sensor unit: Approx. 102 mm ´ 31 mm ´ 22 mm Magnet unit: Approx. 37 mm ´ 14 mm ´ 14 mm R Mass (weight) Sensor unit: Approx. [. . . ]