User manual PANASONIC KX-HNS104FX

[. . . ] Installation Guide Home Network System Glass Break Sensor Model No. KX-HNS104FX Thank you for purchasing a Panasonic product. This document explains how to install the glass break sensor properly. For details about how to use the system, refer to the User’s Guide (page 17). Please read this document before using the unit and save it for future reference. Table of Contents Introduction Accessory information . . . . . . . . . . . . . . . 3 Important Information Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 About this system . . . . . . . . . . . . . . . . . . . . . . 4 For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important safety instructions . . . . . . 5 For best performance . . . . . . . . . . . . . . . . 5 Other information . . . . . . . . . . . . . . . . . . . . . . . 6 Setup Part names and functions . . . . . . . . . . 8 LED indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Setup overview . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Inserting the batteries . . . . . . . . . . . . . . . . 9 Registering the sensor . . . . . . . . . . . . . 10 Confirming the usage area . . . . . . 11 Information about sensor features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appendix Adjusting the sensor sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Features available when using the [Home Network] app . . . . . . . . . . . . . . . . 17 Accessing the User’s Guide . . . . 17 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2 Introduction Accessory information Supplied accessories No. [. . . ] R Do not use benzine, thinner, or any abrasive powder. 6 Important Information Disposal of Old Equipment and Batteries (Only for European Union and countries with recycling systems) Information on Disposal in other Countries outside the European Union These symbols (A, B) are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol These symbols (A, B) on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment. For more information about collection and recycling, please contact your local municipality. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. This symbol (B) might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. Note for the battery removal procedure Refer to “Inserting the batteries” on page 9. 1 2 7 Setup Part names and functions Indicator Green, lit Red, lit Red, blinking Green, blinking slowly Off Status No glass break detected Glass break was detected Sensor is out of range of the hub Registration mode (You pressed and held M N) No battery power A B C D Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 10). E Microphone LED indicator MHIGHN/MLOWN Used to change the sensor sensitivity (page 17). Rear cover M N Used to confirm the status of the sensor or register the sensor to the hub. Setup overview 1 Initial setup Make sure you can access the system using your mobile device. For details, refer to the System Setup Guide included with your hub. Insert the batteries The sensor is battery powered. Registration Required only if the sensor was purchased separately (i. e. , not as part of a bundle). Confirm the installation area Read the information in this document to confirm that the desired installation area is suitable to proper operation. Installation Install the sensor in the desired location. 2 3 LED indicator N and check the You can press M LED indicator to confirm the sensor’s status. After confirming the sensor’s status, we recommend turning the LED indicator off by pressing M N again as soon as possible, otherwise battery life may be reduced. 4 5 8 Setup Inserting the batteries R USE ONLY Alkaline batteries AA (LR6) size. R Do NOT use Manganese/Ni-Cd/ Ni-MH batteries. R Confirm the polarities ( , 3 Install the rear cover. R Place it with the “ ” mark facing upwards and slide it. 1 Remove the rear cover by pressing the upper sides of the cover (A) and sliding it down (B). A B 2 Insert the batteries. Note: R If the sensor’s battery power is low, a message will be displayed on the [Sensor] screen of the [Home Network] app. [. . . ] R 2 37 mm UP 1 UP 2 1 15 Setup Using the wall mounting adaptor 2 1 Remove the rear cover by pressing the upper sides of the cover (A) and then sliding it down (B). A Attach the wall mounting adaptor to the wall by using screws (1). R Place the wall mounting adaptor with “UP” mark facing upwards. R 2 21 mm UP 2 B 1 1 3 Attach the sensor to the wall mounting adaptor. [. . . ]