User manual PANASONIC KX-NT265B

[. . . ] If the power is supplied from the network to the IP-PT [Power-over-Ethernet], disconnect the Ethernet cable. Otherwise, disconnect the AC adaptor cord. · Never attempt to insert wires, pins, etc. into the vents or other holes of this unit. WARNING: TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. [. . . ] Tone CO line access no. --4-- Features List Feature Operation Before Leaving Your Desk To lock 7 7 1 C. Tone Extension Dial Lock To unlock 7 7 0 extension PIN (max. Tone Setting the Telephone According to Your Needs 0 Both Calls Outside Calls Intercom Calls Do Not Disturb 7 1 1 2 1 0 Set Cancel C. Tone Extension Feature Clear To set 7 9 0 C. Tone 7 6 0 1 hour/minute (4 digits) 0 AM Timed Reminder 1 PM 0 1 To cancel once daily C. Tone To stop or answer the ring back 7 6 0 0 C. Tone INTERCOM / To set/cancel for intercom calls 0 7 3 1 1 3 To set/cancel for outside calls No Call Tone C. Tone Receiving Call Waiting 7 3 2 Whisper OHCA 0 1 No tone Tone C. Tone your dealer for more details about the feature numbers. can change the flexible CO buttons to the feature buttons. · "Location of Controls" is shown on page 7. · You · Consult --5-- Settings on the Programming Mode To enter the program mode PROGRAM To exit PROGRAM Operation Loop-CO (L-CO) Single-CO (S-CO) Direct Station Selection One-touch Dialing Incoming Call Distribution Group (ICD Group) CO FWD/DND - Both calls CO 4 4 4 4 4 5 No line 1 2 3 8 9 5 CO 0 1 2 3 CO line no. desired no. FWD/DND - Outside calls FWD/DND - Intercom calls CO CO CO CO Account Conference Log in/ Log-out CO CO CO 0 ICD Group no. CO 0 Preferred Line Assignment-Outgoing 1 9 1 2 3 + CO button no. An idle outside line / CO / INTERCOM A CO/ICD Group button Intercom No line The longest ringing line An assigned outside button 0 Preferred Line Assignment-Incoming 2 0 1 2 0 + CO button no. / CO Ringing (Tone Call) Directly (Voice Call) Ring only No (No tone) Alternate ReceivingRing/Voice 2 1 1 2 Call Waiting for Outside calls Call Waiting Selection Call Waiting Tone Type Selection Extension PIN [Personal Identification Number] (PIN-max. 10 digits) 3 3 3 0 1 2 0 / 1 Yes (Tone) 0 No Call 0 Tone 1 / / 1 Tone 1 / 3 Whisper OHCA Tone 2 To set an extension PIN extension PIN same PIN 9 0 To change a stored extension PIN to new one stored extension PIN new PIN same PIN Station Programming Data Default Set # # --6-- Location of Controls 16 15 14 LCD (Liquid Crystal Display) with Backlight PROGRAM: Used to enter and exit the personal programming mode. REDIAL: Used to redial the last dialed number. INTERCOM: Used to make or receive intercom calls. VOLUME Control Button: Used to adjust the volume. AUTO ANS (Auto Answer)/MUTE: Used to receive an incoming call in hands-free mode or mute the microphone/handset during a conversation. AUTO DIAL/STORE: Used for System/Personal Speed Dialing or storing program changes. Headset Jack TRANSFER: Used to transfer a call to another party. --7-- Location of Controls FLASH/RECALL: Used to disconnect the current call and make another call without hanging up. Microphone: Used for the hands-free conversation. SP-PHONE (Speakerphone): Used for the hands-free operation. 14 15 MESSAGE: Used to leave a message waiting indication or call back the party who left the message waiting indication. 16 Message/Ringer Lamp: When you receive a call, the lamp flashes red. When someone has left you a message, the lamp stays on red. Flexible Outside (CO) Line Buttons: Used to make or receive an outside call. Pressing this button seizes an idle outside line automatically. (Button assignment is required. ) Also used as feature buttons. [. . . ] 3) Place the unit on a flat surface. When you ship the product: Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a postage-paid letter, detailing the symptom to the outside of the carton. DO NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to make repairs. Product service: Panasonic Factory Servicenters for this product are listed in the servicenter directory. [. . . ]