User manual PANASONIC KX-P1082

[. . . ] BAdaptec and EZ-SCSI are trademarks of Adaptec, Inc. BCentronics is a trademark of Centronics Data Computer Corporation. BAdobe and Acrobat are trademarks of Adobe Systems Incorporated. BAll other acknowledgements are trademarks or registered trademarks of their respective holders. [. . . ] Oil Roll Worn out Change the Oil supply roll now. Transfer unit Transfer wearing out Change the Transfer unit soon. 80, 000 pages 15, 000 pages 31, 000 pages 15, 500 pages *1 Transparencies, coated paper and other specialty media will result in shortening the life of a consumable. When replacing the fuser unit, replace the oil supply roll as well. Do not insert the used oil supply roll into the new fuser unit. 79 Care and Maintenance Clearing a Jam sClearing a media jam If the printer has frequent media jams, make sure that you follow these guidelines: BAlways use high-quality laser paper and transparencies. BMake sure that you load specialty media only in the multi-purpose tray and that you set the media thickness switch to the correct setting for the media used. If a media jam occurs, the printer panel reports Jam at <Location>. The <Locations> are the various sensors throughout the paper path, listed as A through E. The following illustration shows the locations of the sensors that report media jams (A through E). Jam at MPT ( P. 88-89) 2nd cassette feeder (option) 80 Care and Maintenance sJam at A 1A # Open the left side door corresponding to the selected media tray. $ Remove the jammed media. # $ % Close the left side door. OR # Remove the media tray. # $ Remove the jammed media from inside the printer. $ % Reinsert the media tray. & Remove the media from inside the access door. & % 88 Care and Maintenance Caution: BIf the fuser knob will not turn, do not force it, or you may damage the fuser. Instead, follow these steps: a) Unlock the fuser by turning the small green thumbscrew counterclockwise. d) Turn the fuser's large green knob to release the jammed media. e) Remove the jammed media from the fuser and the printer. Safety Caution: BThe fuser is hot; to avoid personal injury, turn off the printer and wait 10 minutes for the fuser to cool before touching it. ' Close the front door. 1B (Printing face up) # Open the front door and the right side door. $ Turn the fuser's large green knob counterclockwise to release the jammed media. % Remove the jammed media from the right side of the printer. $ % # & Close the front door and the right side door. 89 Care and Maintenance sJam at E 1 Remove the jammed media from the output tray. OR Pull open the access door (above the plastic output tray) and remove the media. 2 Open and close the front door to clear the error message from the LCD. 90 Care and Maintenance sJam at MPT (Multi-purpose tray) 1 Remove the jammed media from the multi-purpose tray. 2 Open and close the front door to clear the error message from the LCD. 91 Care and Maintenance Troubleshooting Trouble READY indicator is blinking. Possible Cause The printer is receiving, processing or printing job. You have entered the Menu mode in the printer panel. The printer is not ready, is disabled, or has detected an error. [. . . ] It is not recommended that you use envelopes with any of the following characteristics (using these may result in paper jams): BIrregularly shaped envelopes BEnvelopes with curls, wrinkles, nicks, twists, dog-ears or other damage BEnvelopes with side seam construction BHighly textured envelopes, or with extremely shiny surfaces BEnvelopes that seal by removing a peel-off strip BEnvelopes with more than one flap to be sealed BSelf-adhesive envelopes BEnvelopes that are baggy or not sharply creased BEmbossed envelopes BEnvelopes that have previously been printed on Side seam construction Peel-off strip Multiple flaps Twist Curl Bent-edge Wave Dog-ears Self adhesive 130 Appendix Do not attempt to print on any of the following types of envelopes. BEnvelopes with clasps, snaps or tie strings (see Figure 1) BEnvelopes with transparent windows (see Figure 2) BEnvelopes that will melt, discolor, scorch offset or release hazardous emissions when exposed to 200°C (392°F) for 0. 1 second BEnvelopes that use encapsulated types of adhesive that do not require moistening but rely on pressure to seal them Figure 1 Figure 2 Always test a sample of the envelopes you are thinking of buying. Confirm that the envelope performs acceptably. For best printing results BAvoid printing in high humidity i. e. , above 70%. [. . . ]