User manual PANASONIC KX-P1083

[. . . ] · Windows® 98*1, Windows Me*2, Windows 2000*3 or Mac OS 8. 5, 8. 6 or 9. 0 is required for a USB connection. To a computer B USB interface % Power cord C When using the network interface cable (KX-P7110 only): Note: · Use category 5 shielded twisted pair cable with RJ-45 connector C Network interface *1 Microsoft® Windows® 98 operating system (hereafter Windows 98) *2 Microsoft® Windows® Millennium Edition operating system (hereafter Windows Me) *3 Microsoft® Windows® 2000 operating system (hereafter Windows 2000) Printed in China PJQQB0003ZA S0901B0 M s Contents Make sure that all accessories shown below were provided and have not been damaged. Report damage or shortages to the toll free help number located on the back of this guide. Please record important information about your printer in the space provided below. Note: Save the original carton and packing materials for future shipping and transporting of the unit. They have been specifically designed to protect the equipment during shipment. Toner cartridge [KX-PDP7 (For U. S. A) / KX-PDP8 (For other countries)] Drum unit (KX-PDM7) Power cord Printer CD-ROM Setup Guide Network Setup Guide (Included in the KX-P7110 only) Step 3 Installing the Printer Software (For Windows* ) 1 Note: · To connect the printer to a Macintosh computer, With driver for PCL: Download the driver from the follwing site to install it. [. . . ] (3) Click Install Printer driver and Utilities. (4) Follow the instructions on the screen. · When selecting the printer port, click on the Install USB port by Plug and Play check button. ( Press PRINT/RESET button less than 5 seconds to print the configuration page. Note: When using the printer and other USB device simultaneously, we cannot guarantee normal printing. s Using the Printer Software (For Windows) Accessing the Printer Software The printer is accessed from Programs menu or task bar in Windows. For the detailed information, refer to the Operating Instructions. As an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. registered mark. ) BMicrosoft, Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. BMac and Macintosh are trademarks of Apple Computer, Inc. BPentium is a registered trademark of Intel. BAdobe, the Adobe logo, Acrobat, the Acrobat logo and PostScript are trademarks of Adobe Systems Incorporated. BDestinyTM and PageStylerTM are trademarks of Destiny Technology Corporation. BAll other acknowledgements are trademarks or registered trademarks of their respective holders. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75 mm2 or 1. 0 mm2). CAUTION HOT SURFACE FOR USERS IN U. K. IMPORTANT: FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This printer is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS 1362. Check for the ASTA mark ASA FOR USERS IN UNITED STATES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. The user may find the booklet "Something About Interference" available from FCC local regional offices helpful. [. . . ] Remove the jammed media, then open the front cover and close it. Press the PRINT/RESET button (less than 5 seconds). Turn the power off for a few seconds then on again. If the error continues, call for service. Model Number KX-PEM12 KX-PEM13 KX-PPSU5 KX-PMF3 Description 16 MB RAM board 32 MB RAM board Upgrade kit (for PostScript) 2nd feeder ERROR TONER/ DRUM UNIT Supplies Use of supplies other than genuine Panasonic supplies can damage the printer. [. . . ]