User manual PANASONIC KX-P1654

[. . . ] Keep the printer CD-ROM in a safe place for future reference. Do not expose the CD-ROM to direct sunlight or extreme heat and do not scratch or smudge the surface of the CD-ROM. 2 Features Thank you for purchasing a Panasonic Laser Printer. We are sure it will meet your printing needs and give you many years of productive and efficient use. Printing in PCL and PostScript In addition to printing in the PCL Emulation or PostScript® Emulation for Microsoft® Windows® operating system, it also provides compatibility for Macintosh using the PageStyler II driver in the PostScript Emulation. Paper handling Media tray (universal cassette): Supports loading both Letter and Legal 75 g/m2 (20 lb. ) paper up to 250 sheets. Transparency or envelope can be also loaded. [. . . ] -- Do not place the drum unit in a high humid area. · Do not touch electrodes illustrated below to prevent static electricity damage to the printer. Drum Electrodes (shown in red) Settings and Printing Maintenance and Spec. Network 11 Cleaning the Printer 6 Wipe rollers (A) and (B), and paper chute with a soft cloth that has been moistened with a mild commercial cleaner. ·Be sure to remove the paper dust. (B) Paper chute Sheet: Not to damage (A) NOTE · Front rollers (A) can be rotated half. Inner rollers (B) can be rotated to the direction of the arrow. Be sure not to damage the sheets in front of the inner rollers (B). 7 Turn the sponge up and carefully wipe the laser unit cover glass with a dry lint-free cloth. Laser unit cover glass: Not to touch by hand CAUTION To avoid a damage to the printer, · Do not use rubbing alcohol to wipe the laser unit cover glass. · Do not touch the laser unit cover glass by hand. Settings and Printing Maintenance and Spec. Network 12 Cleaning the Printer 8 Carefully wipe the corona wire of the drum unit by sliding a dry cotton swab from end to end a few times. corona wire 9 Firmly insert the drum unit in the slot of the printer (1) [insert the side pins of the drum unit into the groove (label )]. Push down (2). 2 1 Side pin 2 10 Close the front cover and replace the media tray into the printer. Settings and Printing Maintenance and Spec. Network 13 Clearing a Jam Clearing a Jam If the printer has frequent media jams, make sure that you follow these guidelines: · Always use high-quality paper and transparencies (see "Media" on page 53). · Make sure that you load thick paper [106 ­ 165 g/m2 (29 ­ 44 lb. )] or labels only in the manual feed. If a media jam occurs, the printer status display reports "Jam at <Location>". The <Locations> are the various sensors throughout the paper path as illustrated below. Jam at A (see page 17) Jam at B (see page 19) Jam at D Jam at E (see page 24) (see page 25) 2nd feeder (option) Jam at C (see page 22) Jam at OP (see page 14) Jam at STD (see page 14) Settings and Printing Maintenance and Spec. Network 14 Clearing a Jam Jam at STD / Jam at OP When a media feed error has occurred, clear the media feed error as follows: 1 Pull the media tray out of the printer or 2nd feeder (option). 2 Tap the media stack on a level surface to avoid media jams or skewed printing. ·If a media feed error has occurred, remove the media stack from the media tray and tap it. Settings and Printing Maintenance and Spec. Network 15 Clearing a Jam 3 Place the media with the print side down. ·Be sure that the media does not exceed the limit mark. Print side down Paper feeds in direction of arrow. NOTE · If the metal plate is in the up position by accident, the media tray cannot be inserted into the printer. Before loading the media, push down the metal plate until it clicks, locking it in place. 4 Replace the media tray into the printer or 2nd feeder (option). CAUTION · Be sure to hold the media tray with both hands so you do not drop it especially when it is fully loaded. Settings and Printing Maintenance and Spec. Network 16 Clearing a Jam 5 Open and close the front cover to clear the error indication. 2 1 Settings and Printing Maintenance and Spec. Network 17 Clearing a Jam Jam at A 1 Open the front cover. 2 Lift the drum unit up. Settings and Printing Maintenance and Spec. Network 18 Clearing a Jam 3 Grasp both sides of the jammed media and slowly pull it out of the printer. 4 Push the drum unit down. 5 Close the front cover. Settings and Printing Maintenance and Spec. Network 19 Clearing a Jam Jam at B 1 Open the front cover. 2 Lift the drum unit up. Settings and Printing Maintenance and Spec. Network 20 Clearing a Jam 3 Remove the jammed media from the output tray. - Or - Open the rear cover of the printer (1) and remove the jammed media (2). 2 1 CAUTION HOT SURFACE Settings and Printing Maintenance and Spec. Network 21 Clearing a Jam 4 Push the drum unit down. 5 Close the front cover. Settings and Printing Maintenance and Spec. Network 22 Clearing a Jam Jam at C 1 1 Perform the jam recovery steps for Jam at A (see page 17). - Or - Pull the media tray out of the printer. 2 Slowly pull the jammed media (2) out of the printer while pushing the center tab (1) of the jam release pan down. 1 Rear side of Printer 2 Settings and Printing Maintenance and Spec. Network 23 Clearing a Jam 3 4 Replace the media tray into the printer. Open and close the front cover to clear the error indication. 2 1 Settings and Printing Maintenance and Spec. Network 24 Clearing a Jam Jam at D 1 Open the rear cover of the printer (1) and grasp both sides of the jammed media and slowly pull it out of the printer (2). 2 1 CAUTION HOT SURFACE 2 Open and close the front cover to clear the error indication. 2 1 Settings and Printing Maintenance and Spec. Network 25 Clearing a Jam Jam at E 1 1 Perform the jam recovery steps for Jam at D (see page 24). - Or - Pull the media tray out of the printer. 2 Slowly pull the jammed media (2) out of the printer while pushing the center tab (1) of the jam release pan down. 1 Rear side of Printer 2 Settings and Printing Maintenance and Spec. Network 26 Clearing a Jam 3 4 Replace the media tray into the printer. Decrease the media stack so that the height of media does not exceed the limit mark. Check the media usable or not (see "About Media" on page 9 in "Settings and Printing"), (see "Media" on page 53). Install media correctly in the media tray. Check the media usable or not (see "About Media" on page 9 in "Settings and Printing"), (see "Media" on page 53). The print out media is wrinkled. The media is not installed correctly. Incorrect type of media is used. Settings and Printing Trouble The back of the printed page appears dirty. Maintenance and Spec. Possible Cause The transfer roller or fuser unit is contaminated after clearing a jam. Network Corrective Action 32 Troubleshooting Display the Remote Control Panel and select Fuser Cleaning from the Tool menu to print a cleaning data (see "Remote Control Panel" on page 28 in "Settings and Printing"). Use a correct media (see "About Media" on page 9 in "Settings and Printing"), (see "Media" on page 53). Check the length media guide is set to the groove indicating the media size. Check the loaded media is not curled. The toner cartridge has reached the end of useful life. Incorrect type of media is used. Frequent media-picking errors occur. The length media guide of the media tray is not set correctly. The media is not set correctly in the media tray. Check the media is not set on the media height stopper (A) of the length media guide. A Pick up roller is dirty. Clean the pick up roller (see "Cleaning the Printer" on page 8). Image is cut. Adjust the image within the print area (see "Margins and Print Area" on page 12 in "Settings and Printing"). Settings and Printing Maintenance and Spec. Network 33 Troubleshooting If you can't make a print Trouble Printer not operating. Possible The printer may not be plugged into an AC outlet or turned on. The interface cable(s) may not be connected properly. [. . . ] Sets the context used by NDS in the print server name. You may set the print server name (up to 8 servers) to which the KX-P7310 is connected. A time for KX-P7310 to recognize the end of a job in remote printer mode. Printer Name MLPxxxxxx-Printer Operation Mode PSERVER Print Server Name Password Job Polling Time Bindery Mode File Server Name NDS Tree MLPxxxxxx NULL 4 seconds ENABLE NULL NULL NDS Context Print Server Name NULL NULL Time Out 10 seconds Settings and Printing Maintenance and Spec. Network 92 Appendix AppleTalk Name Use AppleTalk Protocol Printer Name Zone Name Factory Default ENABLE KX-P7310-xxxxxx * Description Enables or disables AppleTalk protocol for KX-P7310. The name set here can be seen from Chooser. [. . . ]