User manual PANASONIC KX-P7100

[. . . ] Note: If you do not have a parallel interface cable or USB cable, you will need to purchase one. A Parallel interface # B When using the USB interface cable: Note: · Use a shielded cable 5. 0 m (16. 4 ft) or less in length. · Windows® 98*1, Windows Me*2 or Windows 2000*3 is required for a USB connection. · Please note that if more than one KX-P7100 printers are connected in a USB tree, only one of those printers will perform the print job. $ To a computer B USB interface % Power cord *1 Microsoft® Windows® 98 operating system (hereafter Windows 98) *2 Microsoft® Windows® Millennium Edition operating system (hereafter Windows Me) *3 Microsoft® Windows® 2000 operating system (hereafter Windows 2000) Printed in China PJQQB0002ZA S0501B0 M s Contents Make sure that all accessories shown below were provided and have not been damaged. [. . . ] Refer servicing to qualified personnel. Power Source Warning · The power source voltage of this unit is listed on the nameplate (located on the rear of the printer). Only plug the unit into an outlet with the proper voltage. The voltage level of the power source must not vary more than ±10% from the proper voltage level. · When you operate this equipment, the outlet should be near the equipment and accessible. · To ensure safe operation the AC cord supplied must be inserted into standard three-prong AC outlet which is effectively grounded (earthed) through the normal wiring. · The fact that the equipment operates satisfactorily does not imply that the power point is grounded (earthed) and that the installation is completely safe. For your safety, if in any doubt about the effective grounding (earthing) of the power point, consult a qualified electrician. · If the plug cannot be inserted into the AC outlet, contact a licensed electrician to replace the outlet with a properly grounded (earthed) one. · Do not defeat the purpose of the grounding (earthing) plug (ex. · Do not use an extension cord. Ozone Release Warning Make sure that the printer is installed in a well ventilated room so as not to increase density of ozone in the air. Since ozone is heavier than air, it is recommended that air at floor level be ventilated. Caution Labels CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT CLASSE 1 LASER PRODUIT CLASE 1 LÁSER PRODUCTO (220-240 V equipment) CAUTION HOT SURFACE INSIDE (220 - 240 V equipment) A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75 mm2 or 1. 0 mm2. CAUTION HOT SURFACE FOR USERS IN U. K. IMPORTANT: FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This printer is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS 1362. Check for the ASTA mark ASA FOR USERS IN UNITED STATES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. [. . . ] 9. 5, San Gabriel Industrial Park Carolina, Puerto Rico 00985 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 http://www. panasonic. ca Matsushita Electric Industrial Co. , Ltd. Web Site : http://www. panasonic. co. jp/global/ World Wide Web Support: http://www. kme. panasonic. co. jp/saga/english/index. htm *1 READY ERROR Toner is low. Drum unit is wearing out. Replace the toner cartridge soon. [. . . ]