User manual PANASONIC KX-P8410

[. . . ] Operating Instructions Model No. KX-P8410 Please carefully read the Operating Instructions before operating. Keep this CD-ROM in the protective case. Do not expose the CD-ROM to direct sunlight or extreme heat and do not scratch or smudge the surface of the CD-ROM. BMicrosoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. BPentium is a registered trademark of Intel Corporation. [. . . ] The <Locations> are the various sensors throughout the paper path, listed as A through E. The following illustration shows the locations of the sensors that report media jams (A through E). Jam at MPT ( P. 88-89) 2nd cassette feeder (option) 80 Care and Maintenance sJam at A 1A # Open the left side door corresponding to the selected media tray. $ Remove the jammed media. # $ % Close the left side door. OR # Remove the media tray. # $ Remove the jammed media from inside the printer. $ % Reinsert the media tray. & Open and close the front door to clear the error message from the LCD. 81 Care and Maintenance (2nd cassette feeder) 1B # Open the lower left side door. # $ Remove the jammed media. $ % Close the lower left side door. OR # Remove the selected media tray (middle or lower media tray). # $ Remove the jammed media from inside the printer. $ % Reinsert the media tray. & Open and close the front door to clear the error message from the LCD. 82 Care and Maintenance sJam at B 1 Open the left side door. 2 Use the green handles to pull out the paper feeder. 3 Remove the jammed media on the paper feeder. 4 Reinsert the paper feeder and close the left side door. 83 Care and Maintenance sJam at C 1 Remove the fuser: # Open the printer front door. $ Turn the small green thumbscrew counterclockwise to unlock the fuser. $ # Safety Caution: BThe fuser is hot; to avoid personal injury, turn off the printer and wait 10 minutes (after opening the front door) for the fuser to cool before touching it. % Holding the green tab on the right, slide the fuser out until the safety catch stops it. & Press the green lever on the left to release the safety catch. & % CAUTION: HOT SURFACE INSIDE 84 Care and Maintenance 2 # Hold the fuser as shown below, and slide it out of the printer. Safety Caution: BThe fuser unit weighs approximately 3. 1 kg {6. 8 lbs. }. Take care when handling it. $ Close the front door. # $ 3 Remove the oil supply roll: # Press out on tabs to unlock the oil supply roll. $ Remove the oil supply roll out of the fuser. # # $ Note: BIf the paper is not jammed in the fuser unit, perform the following. # Repeat steps 1 to 4 of Jam B on page 83. $ Skip step 4 and go to step 5. 85 Care and Maintenance 4 # Turn the fuser's large green knob clockwise. $ Remove the jammed media. $ # 5 # Replace the oil supply roll into the fuser. $ Press down firmly on the oil supply roll to snap both sides into place. $ $ # Caution: BIf the oil supply roll is not installed correctly, print quality will be diminished. 6 # Open the front door. $ Slide the fuser back into the printer. $ # 86 Care and Maintenance 7 # Turn the small green thumbscrew clockwise to lock the fuser. $ Close the front door. # $ 87 Care and Maintenance sJam at D Safety Caution: BThe fuser is hot. To avoid personal injury, turn off the printer and wait 10 minutes (after opening the front door) for the fuser to cool before touching it. [. . . ] High humidity may cause the envelope to curl and pick up excess toner. High humidity may also cause the envelope to seal. BAvoid printing below 10°C (50°F) with less than 30% relative humidity. Low temperature with low humidity may cause light printing. [. . . ]