User manual PANASONIC KX-PRXA15E

[. . . ] The handset cover comes attached to the handset. B C D Additional/replacement accessories Please contact your nearest Panasonic dealer for sales information. Accessory item Rechargeable batteries Model number HHR-4MVE*1 Battery type: – Nickel metal hydride (Ni-MH) – 2 x AAA (R03) size for each handset KX-A405 KX-TGA20EX*2 DECT repeater Key finder *1 *2 Replacement batteries may have a different capacity from that of the supplied batteries. By registering the key finder (4 max. ) to a Panasonic Digital Cordless Phone and attaching it to an easy-to-lose item in advance, you can locate and find the mislaid item to which the key finder is attached. [. . . ] a MOKN a M N Changing the base unit PIN Important: R If you change the PIN (Personal Identification Number), please make note of your new PIN. The unit will not reveal the PIN to you. If you forget your PIN, see page 52. 1 2 3 4 MMenuN (right soft key) #104 Enter the desired name (max. a MOKN 2 times a M N 1 2 3 4 MMenuN (right soft key) #132 Enter the current 4-digit base unit PIN (default: “0000”). a MOKN MbN: “Yes” a MOKN a M N Call restriction You can restrict selected handsets from dialling certain numbers. You can assign up to 6 phone numbers to be restricted, and select which handsets are to be restricted. Storing area codes here prevents the restricted handsets from dialling any phone number in that area code. Calendar/Schedule You can program 20 schedule alarms for each handset using the calendar. A schedule alarm sounds at the set time for 1 minute. A text memo can also be displayed for the schedule alarm. Important: R Make sure the unit’s date and time setting is correct (page 13). 1 2 3 MMenuN (right soft key) #256 Enter the base unit PIN (default: “0000”). Select the handsets to be restricted by pressing 1 to 6. a N MOKN 2 times a M Erasing an entry Schedule alarm entries are not erased automatically after the schedule alarm sounds. Erase unwanted entries. 1 2 3 4 1 32 MMenuN (right soft key) a a MOKN Registering a handset to a base unit The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit (for example, is displayed even when the handset is near the base unit), re-register the handset. MListN a MbN: Select the desired entry. MMenuN a MbN: “Erase” a MOKN MbN: “Yes” a MOKN a M N Erasing all entries MMenuN (right soft key) a a MOKN 1 Handset: MMenuN (right soft key) #130 Helpline Tel. 0844 844 3899 Ireland 01289 8333 PNQX6032YA_0529_ver110. pdf 32 2013/05/29 12:39:48 Programming 2 3 MbN: Select a base unit number. a MOKN R This number is used by the handset as a reference only. Base unit: Press and hold M N for about 5 seconds. R If all registered handsets start ringing, press M N again to stop, then repeat this step. Handset: MOKN a Wait until “Base PIN” is displayed. a Enter the base unit PIN (default: “0000”). a MOKN R If you forget your PIN, see page 52. 2 3 MbN: Select the base unit you want to cancel. [. . . ] R You are entering the wrong remote access code. If you have forgotten your remote access code, enter the remote access code setting to check your current code (page 45). R If the first ring is turned off, the number of rings decreases by 1 from the specified number of rings. The unit does not emit the specified number of rings. Liquid damage Problem Liquid or other form of moisture has entered the handset/base unit. Cause/solution R Disconnect the AC adaptor and telephone line cord from the base unit. [. . . ]