User manual PANASONIC KX-PS8100

[. . . ] Operating Instructions Model No. KX-PS8100 Please carefully read the Operating Instructions and the Utilities and Drivers Reference Guide before using the Digital Color Imaging System. Keep this CD-ROM in the protective case. Do not expose the CD-ROM to direct sunlight or extreme heat and do not scratch or smudge the surface of the CD-ROM. Thank you for purchasing the Panasonic Digital Color Imaging System (DCIS) KX-PS8100. The Panasonic Digital Color Imaging System KX-PS8100 consists of the Color Laser Printer KX-PS8101 and the Color Scanner KX-PS8102. The serial numbers are located on the labels on the rear of the units. For your convenience, record these numbers below and keep this book along with your proof of purchase, in the event of a theft or for future reference. [. . . ] Use the arrow buttons to select numbers in the address. Press the ENTER button to accept your selection. Gateway Address [127. 0. 0. 1*] Use this option to specify the gateway address for printing with TCP/IP. If your TCP/IP network has a gateway and you plan to print using TCP/IP, you must enter the gateway address. (*=Default setting) B) When you select AppleTalk Setup: AppleTalk Setup To advance to the next screen, press the ENTER button. Yes/No [No*] Select YES if you have an AppleTalk network connected to the printer. Note that you can enable AppleTalk, TCP/IP, and IPX (Novell) communication simultaneously. NOTE: The following option is displayed only if AppleTalk is enabled. AppleTalk Zone Select the AppleTalk zone in which you want the printer to appear. If you do not select a zone, the printer is assigned to the default AppleTalk zone. (*=Default setting) 149 Setup from the Printer Panel and WebSetup C) When you select IPX/SPX Setup: IPX/SPX Setup To advance to the next screen, press the ENTER button. Yes/No [No*] Select Yes if you have an IPX (Novell) network connected to the printer. Note that you can enable AppleTalk, TCP/IP, and IPX (Novell) communication simultaneously. (*=Default setting) Language Setup The panel language setup menus are used to select a language for the printer panel. Language Press the ENTER button to view language options. Menu Mode English/Franais/Deutsch/Espaol/Italiano [English*] Select a language for the printer panel and Configuration page. (*=Default setting) Reset Queues This screen appears only if an optional hard disk drive is installed. Resetting the queues clears all jobs from the Hold and Print queues, all Check and Print jobs, and the Job Log. It does not affect print option settings specified in Setup from the printer panel or from Fiery WebSetup. Reset Queues Yes/No [No*] (*=Default setting) Hard Disk This screen appears only if an optional hard disk drive is installed. If you select Yes, all data on the hard disk drive is deleted, including jobs in the Hold and Print queues, Check and Print jobs, and the Job Log. Yes/No [No*] (*=Default setting) 150 Setup from the Printer Panel and WebSetup Completing setup from Fiery WebSetup After you have performed an initial Setup from the printer panel (see page 145), you must complete the process of configuring Setup options using Fiery WebSetup, one of the Fiery WebTools. You can also use Fiery WebSetup to remotely view and modify Setup options later. Before you can access the Fiery WebTools, you must complete the following: Initial Setup, specifically, setting the printer's IP address, and subnet mask as well as its gateway from the printer panel; see page 145. The procedures described in "Setting up Fiery WebTools" on this page. Setting up Fiery WebTools Fiery WebTools allow you to manage your KX-PS8100 remotely from the Internet or from your company's intranet. [. . . ] 148 Network settings using Fiery WebSetup. 75 Novell NetWare (shell version 3. 26 and above) option . 126 M Macintosh computers installing PostScript printer driver . 204 Microsoft Internet Explorer, see Internet Explorer MPT (Multi-Purpose Tray) . [. . . ]