User manual PANASONIC KX-T3806BE

[. . . ] 18 Connecting the Handset/Telephone Line Cord . 17 Advanced Operation Speed Dialer . 23 Temporary Tone Dialing (For Rotary or Pulse Service Users) . 23 How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) . [. . . ] If a wrong PIN code is entered, 3 beeps will sound. Enter the correct PIN code and press (PROGRAM). To return to the standby mode, lift the handset and hang up. 6 7 Enter a new PIN code using a 4-digit number. "1234" is entered. ) Press (PROGRAM). A long beep sounds. The unit will return to the standby mode. Please write down your PIN code. If you forget your PIN code, call our customer call center at 1-800-211-PANA(7262). 26 " Dial Lock You can prevent others from making a call to any number except the one pre-programmed in the memory of the EMERGENCY button. Once you locked the dialing buttons, even emergency numbers cannot be dialed. Only incoming calls are accepted until the dial lock is canceled. Before using this feature, we recommend storing an emergency number in the memory of the EMERGENCY button (p. Even if the dialing buttons are locked, the number stored in the button can be dialed. If you choose not to program emergency numbers, but plan to use the dial lock, any number programmed into the EMERGENCY button can be accessed. M IC (EMERGENCY) To set the dial lock 1 2 3 Press (DIAL\LOCK). " " flashes on the display. Enter the PIN code (p. Press (PROGRAM). " " is displayed. To order, call the accessories telephone number on page 3. " Connecting an Optional Headset to the Unit Connect an optional headset to the headset jack as shown below. The illustration headset is a KX-TCA90. Headset Jack Hook Microphone Earpiece Useful Information If you want to have a normal conversation, disconnect the headset. For assistance, please call: 1-800-211-PANA(7262) 29 " Optional Headset Making/Answering Calls Make sure to install the batteries. VOLUME (_), (^) (SP-PHONE/HEADSET) and Indicator 1 2 Press (SP-PHONE/HEADSET) to make or answer a call. The SP-PHONE/HEADSET indicator flashes. If you misdial when making a call, press (SP-PHONE/HEADSET) twice and dial again. To hang up, press (SP-PHONE/HEADSET). The indicator light goes out. To adjust the headset receiver volume (4 levels): While using the headset, press VOLUME (_) or (^). During a conversation using the headset, you cannot switch the call to the handset by lifting it off the cradle. If you disconnect the optional headset during a conversation with the handset on the cradle, the call will be switched to the speakerphone. During a conversation using the speakerphone, you can switch the call to the headset by connecting the headset. 30 Battery Replacement If " " flashes, the battery power is low. Replace the batteries within 1 minute to keep the programmed settings. But the programmed time setting will be cleared. + + + - 1 2 1 Disconnect the telephone line cord from the unit. 2 Press down in the direction of the arrow and remove the cover. 3 4 Replace the batteries with new ones using correct polarity (i, j), and close the cover. Connect the telephone line cord to the unit. " flashes after replacing the batteries, If the time is shown as "12-00" and " readjust the time. Battery Precautions: The batteries should be used correctly, otherwise the unit may be damaged by battery leakage. --Do not mix different types of batteries. --Do not charge, short-circuit, disassemble, heat or dispose of in fire. --Remove all the batteries when replacing. Note: --If you do not install the batteries or if the battery power is low, the time will be shown as "12-00" and " " will flash. --Replace all the batteries once a half year in use of Alkaline batteries, or misoperation may occur. [. . . ] Perform such activities in the off-peak hours, such as early morning hours or late evenings. 36 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]