User manual PANASONIC KX-T5006E

[. . . ] 4 Location of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Settings Connecting the Handset /AC Adaptor/ Telephone Line Cord . . . . . . . . . . . . . . . . . . . . . . . . . 9 Connecting a Communication Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · In some cases, you may have to edit the number before dialling (see below). · If a phone number is not displayed in the caller information, you cannot call back that caller. 4 After editing, you can continue with calling back or storing procedures. To call back, lift the handset or press {SP-PHONE/HEADSET}. To store the number in the Phonebook memory, follow steps 4 to 5 on page 28 to complete the operation. To store the number in the Direct Dial memory, follow steps 4 to 6 on page 29 to complete the operation. Editing a Caller List Information You can edit a phone number recorded in the Caller List. · To exit the Caller List during editing, press {EXIT} or wait for 60 seconds. · The number edited in step 3 will not be maintained in the Caller List. 1 2 Press {4} or {3} to enter the Caller List. Scroll to the desired caller by pressing {4} or {3}. 27 Caller ID Service Storing Caller List Information in the Phonebook You can store numbers that are in the Caller List in the Phonebook. Make sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. 5 Press {OK} (Save key). JACK SMITH 123456789 · A long beep sounds. · The display will return to Caller List. To exit the Caller List, press {EXIT} or wait for 60 seconds. 1 2 3 Press {4} or {3} to enter the Caller List. Scroll to the caller you want to store in the Phonebook by pressing {4} or {3}. Press {OK} (Yes key). To erase a specific caller from the Caller List All erased 1 2 Press {4} or {3} to enter the Caller List. Scroll to the caller you want to erase from the Caller List by pressing {4} or {3}. · A long beep sounds and all entries are erased. · The unit will exit the Caller List. 123456789 1 :5 23 NOV. 3 Press {ERASE}. Erased · A long beep sounds and the information is erased. · After a few seconds, the display will show the previous caller information. · To exit the Caller List, press {EXIT} or wait for 60 seconds. 30 Phonebook Storing Names and Numbers in the Phonebook You can store up to 50 names and phone numbers in the memory. Make sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. 6 Press {OK} (Save key). · A long beep sounds. · To continue storing other items, repeat from step 2. Tom Jones 987654321 C 1 2 3 Press {FUNCTION/EDIT}. Press {OK} (Yes key) at "Save phonebook ?". · The number of stored items is also displayed. Enter a name, up to 15 characters using the dialling buttons (p. 32). · To move the cursor, press {:} or {9}. · If a name is not required, go to step 4. · If the display shows "Phonebook full" in step 2, press {EXIT} to exit the list. To erase other stored items from the Phonebook, see page 35. [. . . ] · If your unit is connected to a telephone line with DSL service, we recommend connecting a noise filter between the base unit and the telephone line jack. Answering System Problem The answering system is on, but incoming messages are not recorded. · Do not pause for over 60 seconds while searching. · If the last number dialled was more than 32 digits long, the number will not be redialled correctly. Cause and Remedy · The recording time is set to "Greeting only". [. . . ]