User manual PANASONIC KX-T7735B

[. . . ] To dial assigned as a One-Touch Dialing button Calling an operator To set KX-TA624 3 KX-TA1232 personal speed dial no. (Check the type of your Main Unit. ) Speed Dialing (Personal) desired no. To dial KX-TA624 personal speed dial no. 3 To dial KX-TA1232 (Check the type of your Main Unit. ) Speed Dialing (System) system speed dial no. ­2­ Features List Desired Feature Operation Receiving Calls Handsfree answerback (Other than KX-T7750) While on-hook Outside (CO) Line (KX-TA1232 only) Directed Picking up a call extension no. (Check the type of your Main Unit. ) Group KX-TA624 KX-TA1232 When the Dialed Extension is Busy/No Answer Automatic Callback Busy To set While hearing a busy tone To call If you hear callback ringing To leave a notification To cancel a notification Sender KX-TA624 receiver's extension no. KX-TA1232 receiver's extension no. Message Waiting (Check the type of your Main Unit. ) To call back To clear all notifications Receiver KX-TA624 your extension no. [. . . ] VOLUME KEY (KX-T7720/7750): Used to adjust the volume. 14 Programmable Feature (PF) Button: Used as an One-Touch Dialing button (Button assignment is required). 15 Flexible Outside (CO) Line Button: Used to make or receive an outside call. Pressing this button seizes an idle outside line automatically. (Button assignment is required. ) Also used as feature buttons. (Button assignment is required. ) PAUSE: Used to insert a pause during dialing. MESSAGE: Used to leave a message waiting indication, or call back the party who left the message waiting indication. Message/Ringer Lamp: The Message/ Ringer lamp informs you visually that you have a message or a call. When you receive a call, the lamp flashes depending on the ringing pattern. When the ringing pattern is set to Single (Slow flash), Double (Moderate flash), or Triple (Rapid flash) in your PBX, the lamp flashes. When the other ringing patterns are set in your PBX, the lamp may not flash. When someone has left you a message, the lamp is lit continuously. 10 11 12 16 17 18 Initial Settings Speaker volume * While on-hook or during a conversation SP-PHONE Handset/Headset volume * While using the handset or headset Press SP-PHONE. Press Up or Down. Press Up or Down. Ringer volume/Backlight illumination 2 0 1 BACKLIGHT Display contrast * KX-T7730/7731/7735/7736 RINGER Slide the lever of the RINGER Volume Selector and BACKLIGHT Illumination Selector to the desired setting. BACKLIGHT SW POSITION 2 1 LCD backlight HIGH LOW DIALING BUTTONS backlight AUTO AUTO 0 OFF OFF Press Left or Right. AUTO: The backlight shines only during operation. * The above settings may return to default settings if the telephone line cord is disconnected, or the main unit's power is interrupted. ­9­ Connection The telephone line cord (included) To the main unit ( TO MAIN UNIT ) /PABX < Back view> Headset CAUTION Ensure the cord is inserted in the groove to prevent damage to the connector. Wall Mounting 1 Pull down the handset hook until it locks, so the tab holds the handset. 2 Remove the attached stand. 2 1 3 Mount the unit on the wall. To temporarily place the handset down during a conversation, hook it over the top edge of the phone as shown. * KX-T7735 model illustrated on this page. ­ 10 ­ Exhibit J - Customer Information This equipment complies with Part 68 of the ACTA rules and the requirements adopted by the ACTA. On the exterior of the cabinet of this equipment is a label that contains, among other information, a product identifier in the format ACJGTB-32973-MF-E/ACJGTB-43121-MF-E. If requested, this number must be provided to the telephone company. ACTA Registration Number (KX-TA624): ACJGTB-32973-MF-E (KX-TA1232): ACJGTB-43121-MF-E Ringer Equivalence Number (REN): 0. 4B Facility Interface Code (FIC): 02LS2 Service Order Code (SOC): 9. 0F USOC Jack Type (KX-TA624): RJ11 (KX-TA1232): RJ11 and RJ14C A FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant. See Installation Instructions for details. If this equipment KX-T7731/36 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. The telephone company may make changes to it's facilities, equipment, operations or procedures that could affect the operation of the equipment. [. . . ] Keep the unit away from heating appliances and electrical noise generating devices such as fluorescent lamps and motors. The unit should be kept free of dust, moisture and vibration, and should not be exposed to direct sunlight. Do not use benzine, thinner, or any abrasive powder to clean the cabinet. Dangerous electrical shock could result. [. . . ]